AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 54 kN/m, LAB = 1.8 m, LBC = 3.6 m, and LcD = 1.8 m. Consider the entire 7.2 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). A LAB B W LBC LCD WT305 x 41

AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 54 kN/m, LAB = 1.8 m, LBC = 3.6 m, and LcD = 1.8 m. Consider the entire 7.2 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). A LAB B W LBC LCD WT305 x 41

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam and loading shown, check if the maximum bending stress is less than the allowable bending stress using the ASD approach. The self-weight of the beam is denoted "waw", and the steel beam is a "W10x26". Assume the beam has an allowable stress due to bending of 21 ksi. See the next page for section properties of the steel beam. Assume the steel cross-section is being bent about its "strong axis" - i.e. the "x-axis". PL = 5.0 kip Wsw B 10 ft
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 18 kips, w = 5.6 kips/ft, LAB = 5.0 ft, LBC = 5.0 ft, and LCD = 13.6 ft. Determine the magnitude of the maximum bending stress in the beam. LAB LBC LCD Answer: i ksi Omax
I need the answer quickly
Please help, I promise to give good feedback. Please do not just guess. Thank you!
AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 56 kN/m, LAB = 1.0 m, LBc = 2.0 m, and LCD = 1.0 m. Consider the entire 4.0 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). y LAB LBC LCD WT305 x 41 Answer: (a) OmaxT= MPa (b) Ơmax.C = MPa
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 23 kips, w = 4.2 kips/ft, LAB = 3.4 ft, LBC = 3.4 ft, and LcD = 15.6 ft. Determine the magnitude of the maximum bending stress in the beam. B |C LAB LBC LCD Answer: Omax = ksi
A WT305 x 41 standard steel shape is used to support the loads shown. Assumew= 40 kN/m, LAB = 1.2 m, LBc = 2.4 m, and LCD = 1.2 m. Consider the entire 4.8 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). В LAB LBC LCD WT305 x 41
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.
The stiffness matrix of the beam shown below is - 1. (2 В El 2EI 4m 8m A.
Solve everything asked in the question with proper SFD and BMD diagrams.
AWT305 x 41 standard steel shape is used to support the loads shown. Assume w= 58 kN/m, LAB = 1.8 m, LBc=3.6 m, and Lco = 1.8 m. Consider the entire 7.2 m length of the beam and determine: (a) the maximurm tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). y LAB LBC LCD WT305 x 41 Answer: (a) Omax,T МPа (b) omax,C= МРа
Question (3). Design Exercise (Selecting initial dimensions) A steel cross section of a bridge deck is shown in Figure 3. The cross section is subjected to a maximum bending moment of 43810 kNm. The length L is 4m. Available plate thicknesses (t) are 20 mm, 22 mm and 25 mm. The yield strength () is 355 MPa. Determine the initial dimensions of b and Cw, which can be used for detailed design of the bridge deck. Assume failure of the cross section mainly governs by in-plane bending. State all other assumptions made during this calculations. 60° 2b Ma