AW18 x 40 standard steel shape is used tosupport the loads shown on the beam. AssumeP = 25 kips, w = 4.0 kips/ft, LaB = 3.4 ft, Lâc = 3.4ft, and Lcp = 15.6 ft. Determine the magnitudeof the maximum bending stress in the beam.PAnswer:OmaxiksiBLAB LBC=♫|CWLCDDX

Answered: Image /qna-images/answer/920443f0-7b9c-4738-a49f-9d32b542792d.jpg

AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 4.0 kips/ft, LAB = 3.4 ft, LBC = 3.4 ft, and LcD = 15.6 ft. Determine the magnitude of the maximum bending stress in the beam. P Answer: Omax i ksi B LAB LBC = |C W LCD D

AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 4.0 kips/ft, LAB = 3.4 ft, LBC = 3.4 ft, and LcD = 15.6 ft. Determine the magnitude of the maximum bending stress in the beam. P Answer: Omax i ksi B LAB LBC = |C W LCD D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

AWT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAB = 2 m, LBC= 5 m, LcD = 1 m, PA = 12 kN, WBC = 12 kN/m. Consider the entire 8-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. A PA LAB Answers: (a) OT = (b) oc = B i 62.19 i 25.81 WBC LBC 1 WT305 x 41 C LCD 88.9 mm 211.1 mm MPa. MPa. D x
For the beam shown at right, determine the following: P= 1800 lb a. Maximum tensile bending stress b. Transverse shear stress at a the junction of the "TEE" (i.e., 2" above the neutral axis). c. Transverse shear stress at the neutral axis - 7.5 ft- - 7.5 ft- (a) d. Draw the stress elements -10 in. representing the state of stress at the junction of the “TEE" and at the neutral axis. | 2 in. 4 in. -N- 1600 10 in. 8 in. 42 in.k- (b)
The dimensions of a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm. Using f’c = 28 MPa, long bar fy = 415 MPa, calculate the required amount of tensile reinforcement so that a tensile strain of 0.005 is attained under a sustained ultimate bending moment of 1,200 kN.m. Compression bars centroid is 70 mm from beam edge. 4,387 3,839 6,180 5.353
Need correct solution. If C is the mid-point of PQ; What is the magnitude of bending moment at fixed end O?
The rod is supported by smooth journal bearings at A and B that only exert vertical reactions on the shaft. Part A Determine its smallest diameter d if the allowable bending stress is oallow = 130 MPa (Figure 1) Express your answer with the appropriate units. HA ? d = Value Units Figure < 1 of 1 Submit Request Answer 12 kN/m Provide Feedback 3 m 1.5 m
What are the distances from the neutral axis to the top and bottom surfaces? If posible was is the second moment of area? in in^4
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 27 kips, w= 2.8 kips/ft, LAB = 3.0 ft, Lsc = 3.0 ft, and Lco = 16.4 ft. Determine the magnitude of the maximum bending stress in the beam. B |C LAB LBC LCD Answer: ksi Omax
A beam is simply supported on a span of 10 m. The beam supports a load of 15 kN/m on its entire length and three 30 kN loads at its quarter points. If the maximum bending stress is equal to 250 MPa, determine the most economical W-shaped beam. OW 530 x 72 O W 510 x 70 O W630 x 65 O W440 x 83
The beam in (Figure 1) is made from three boards nailed together as shown. Figure d 20 mm 25 mm ✓ 200 mm M 150 mm 2 20 mm 1 of 1 Part A If the moment acting on the cross section is M = 460 Nm, determine the resultant force the bending stress produces on the top board. Express your answer to three significant figures and include appropriate units. F = Value Submit μA Provide Feedback 3 Request Answer Units ?
The beam is supported by a pin at point A and a roller at kN point B. A distributed load of W₁ = 8 - and an applied m force of F₁ = 12 kN are applied to the beam. The beam has an allowable bending stress of allow = 6 MPa. Neglect the weight and thickness of the beam. Take the origin for all functions to be at A., i.e. start at the left and go right. Must use positive sign convention for V and M. d3 1 d3 d1 W1 d1 B O h d2 F₁ Values for the figure are given in the following table. Note the figure may not be to scale. Dimensions for the whole beam Variable Value d₁ 4 m d₂ 2 m
q3