AW14X 53 structural steel [E = 29,000 ksi] section (see Appendix B for cross-sectional properties) is used as a column with an actual length of L= 16.0 ft. The column is fixed at its base and unrestrained at its upper end. Determine the maximum load P that may be supported by the column if a factor of safety of 1.8 with respect to buckling is specified. L.

AW14X 53 structural steel [E = 29,000 ksi] section (see Appendix B for cross-sectional properties) is used as a column with an actual length of L= 16.0 ft. The column is fixed at its base and unrestrained at its upper end. Determine the maximum load P that may be supported by the column if a factor of safety of 1.8 with respect to buckling is specified. L.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.10P: If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same...

See similar textbooks

Similar questions

A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
O 88 130% v - + I Annotate T| Edit Trial expired Unlock Full Version ENGR 263 + A A A T O 4.10 Member AB is the beam under consideration. As shown in the illustration of the loading condition, member AB is an overhanging beam that supports a uniformly distributed roof load of 500 lb/ft. It also carries concentrated loads from a rooftop HVAC unit (4000 lb), an interior hanging display support (2000 lb), and a marquee sign (3000 lb). Marquee overnang Displau SLIPPort II Raof Kiots Ol I W = 500 Ib/Ft A B 4000 b 2000 000 I Steel beam !! I1 3 FE 5 FE - Ft RoOFtop HVAC unit 10 FE 4 Ft Marquee sign< R R2 Steel beam (negligible weight) Free-body diagram Dispiay Support Loading condition
SITUATION 2 Determine the safe service load W permitted for this beam-column that is not part of a frame system. Assume ASTM A992 (Fy = 350 MPa; Fu = 450 MPa) as material. Use LRFD specifications. Servise koada P= 30 kips dead load 80 kips live koad Assume hinged for both principal 10- 0 directions W- 20 dead load 8OG live load 10-o Fined for both principal directions Type your final answer/s in the text box provided below.
ASSIGNMENT #5 BIAXIAL BENDING Problem: Check the beam shown for compliance with the NSCP Specification. Lateral support is provided only at the ends, and A992 steel is used, F, = 345 mPa. The 90 kN service loads are 30% dead load and 70% live load. a. Use LRFD b. Use ASD d tw by ty 1x(106) S(10³) mm mm mm mm³ mm mmª W410x100 415 10 260 16.9 398 1920 SECTION Tx mm 177 1m 90 kN 90 KN 1.5m W410x100 I Loaded Section Ly(106) Sy(10³) Ty mmª mm³ mm 49.5 381 62.4 1m Zx(10³) Zy(10³) mm³ mm³ 2130 581
7 7a 7b 7c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is structural tubing however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? The section is 8" x 8" x 7.94 mm thick: Use Fy=248 MPa: E=200,000 MPa AISC wall thickness Ix 106 S x 103 Jx 103 mm4 mm3 mm4 rx =ry Area Ag (mm2) mm Designation Weight/m 8x8 7.94 47.36 6,039 79.25 37.84 371.99 60.35 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narative form to support your cho'ce) 8x8 14.29 80.61 10,258 76.2 59.52 585.02 99.06 8x8 72.7 9,290 76.96 54.53 539.13 90.32 8x8 9.53 56.09 7,161 78.48 44.12 432.62 70.76 mm 12.7 Zx 103 mm3 437.53 714.48 650.57 512.92
Question 1 Check that the medium-term load of 38 kN applied to the spaced column shown in below complies with the design requirements of BS 5268-2. The column consists of two 38 x 150 C22 timbers 76 mm apart. All joints are glued and intermediate packs are 250 mm long. suitable connection #### x ->89² 6:38. Y T -end blocking AP 100 intermediate blocking L₂ 1₁ x W L W EFH 400 m 38kN medium term load -ICHICHID -200 600 600 600 600 600 600 200 38kN medium term load
The tension member is fastened togother using two bolts, one on each side of the member as shown. Each bolt has a diameter of 0 3 in The allowable shear stress for the bolts is Tall 12 ksi and the allowable average normal stress is oallow- 19 ksi Part A Determine the maximum load P that can be applied to the member Express your answer to three significant figures and include appropriate units. Pas Value Units
A 1.5" x1.5" solid steel bar is made of a steel having an Fy = 50 ksi and an Fu = 65 ksi. It is loaded in tension by the following unfactored forces: • DL = 30 kips ● LL = 50 kips • SL 10 kips = Determine if the bar yields in tension. Assume LRFD. Use the ASCE 7-22 Load Combos and Factors.
HOMEWORK-1 3m IF For the truss shown in the figure; Design members 1-2 and 2-3 assuming that out of plane deflections are restrained and Ner>>10, i.e. global buckling is not the critical failure mode and therefore linear static analysis is sufficient. P.S. Use square rectangular hollow sections in Grade 355 steel. You will have to find the related section tables from the internet. Do not forget to refer to the related EN1993-1-1 tables and equations. Later, you will design the connections (the weld lengths, etc.) and the supports for this problem.
1. A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E= 200 GPa. Use AISC/NSCP Specs. 450 mm -cover plate 'I 12 mm y2 IP d2 10 m C 310 x 37 A = 4720 mm? d = 305 mm bf = 77 mm tf = 12.7 mm tw = 9.8 mm C 310 X 37 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. tw d=305- Ix = 59.9x10° mm ly = 1.85x10° mm x = 17.1 mm x=17.1
2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KN