A turbine receives water from a large reservoir and dischargesthe water into the atmosphere, if pipe dia. = 18 in. pipe length=150 ft, and the velocity in the pipe = 20 ft/s, find the powerderived to the turbine by the water, take the major losses (f =0.03)?Water200 ftTurbine20 fus

Given:- d=18in L=150 ft v=20 ft/s To find:- power

Answered: ater into the atmosphere, 1 t, and the…

Engineering

Civil Engineering

ater into the atmosphere, 1 t, and the velocity in the ed to the turbine by the w

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A jet of water issues from a 5-cm diameter nozzle, held vertically upwards, at a velocity of 20 m/sec. If air resistance consumes 10% of the initial energy of the jet, then it would reach a height; above the nozzle, of
4.112. The turbine extracts from the flowing water half as much energy as remains in the jet at the nozzle exit. Calculate the power of the turbine. Water 300 mm d 300 mn d 30 m 300 mm d 300 mm d 150 mm d Problem 4.112 Problem 4.113 4.113. This turbine develops 75 kw when the flowrate is 0.6 m/s, what flowrate may e expected if the turbine is removed?
A turbine system is harnessing the energy of flowing water from reservoir 1 to reservoir 2. The difference in elevation between the two reservoirs is 120ft. For a design flowrate of 50ft^3/s, the head loss is 30ft. Solve the theoretical power extracted by the turbine. Neglect the difference in atmospheric pressure between the reservoirs. O 511hp O 402hp O 245hp O 281hp
A rectangular channel having a width of 3 m. carries water flowing at a rate of 20 m3/s. If the depth of water in the channel is 1.2 m., compute the critical kinetic energy in meter. a. 1.290 b. 0.480 c. 0.825 d. 2.567
Specific energy of flowing water through a rectangular channel of width 5 3 m when discharge is 10 m³/s and depth of water is 2 m is:
The air shed over a city can be considered by a completely stirred tank reactor (CSTR) model with two sides of 2×10° m in length and a mixing depth of 500 m. Horizontal wind blows at 4 m/s from one side of the box and exits from the opposite side. Assume that within the box, the air is well mixed all the time. Within the air shed, benzene (C6H6) is emitted by automobiles, power plants, and factories at a rate of 0.4 kg/s. No benzene is brought to the city by wind. When equilibrated, what is the benzene concentration in the atmosphere? Please sketch the model first. Pay attention to the units.
An oil pump is drawing 18 kW of electric power while pumping oil with density 860 kg/m³ at a rate of 0.1 m³/s. The inlet and outlet diameters of the pipe are 8 cm and 11 cm, respectively. If the pressure rise of oil in the pump is measured to be 250 kPa and the motor efficiency is 95 percent, determine the mechanical efficiency of the pump. Take the kinetic energy correction factor as 1.05. Pump 8 cm D.cm ΔΡ = 250 kPa 18 kW Motor Oil 0.1 m³/s The mechanical efficiency of the pump is %.
An oil fluid flows through pipe with a constant diameter. Determine the total energy head (in meter) at point A from the datum line 3 meters below the point B. po = 900kg/m3, PA = 50 kPa, pg = 94.10 kPa. 0.75 m A 5 m 2 m/s 30 B
I need the answer as soon as possible
A horizontal jet of 57 liters/sec strikes tangentially on one or another of a series of moving curved vanes, each having a deflection angle of 60 degrees. The water as it leaves the vane has an absolute velocity of 12 m/sec and makes an angle of 30 degrees with the horizontal. (a) Determine the horizontal force exerted on the vanes. (b) Determine the power developed.
Specific energy of flowing water through a rectangular channel of width 5 m when discharge is 10 m³/s and depth of water is 2 m is:
Suppose the pump of Fig. is situated between two water tanks with their free surfaces open to the atmosphere. Which free surface is at a higher elevation—the one corresponding to the tank supplying water to the pump inlet, or the one corresponding to the tank connected to the pump outlet? Justify your answer through use of the energy equation between the two free surfaces.