At what depth would the total vertical stress in a deposit of clay (e = 0.9, Gs = assume, consider 4 significant figures) overlain by 3 meters of sand (e = 1.1, assume Gs with 4 significant figures) be 220 kPa if the water table is 2 meters below the ground surface and saturation of 20 percent exists above it? What is the effective stress at the same depth? Draw your stress diagrams up until 2 meters deeper than the point at which the stress is 220 kPa.

At what depth would the total vertical stress in a deposit of clay (e = 0.9, Gs = assume, consider 4 significant figures) overlain by 3 meters of sand (e = 1.1, assume Gs with 4 significant figures) be 220 kPa if the water table is 2 meters below the ground surface and saturation of 20 percent exists above it? What is the effective stress at the same depth? Draw your stress diagrams up until 2 meters deeper than the point at which the stress is 220 kPa.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.8P

See similar textbooks

Similar questions

2. A borehole at a site reveals the soil profile shown. Assume Gs = 2.70 for all soil types. a. What is the unit weight of the soil in layer 1 in kN/m³? b. What is the effective stress at a depth of 2m below the ground surface, in kPa? c. What is the effective stress at a depth of 20.6m below the ground surface, in kPa? Elevation (m) Very fine wet sand with silt 5%, S = 40% Layer 1 2.0 Fine sand saturated by capillary action Layer 2 3.0 Fine sand, w = 12% Layer 3 5.4 Layer 4 Soft blue clay, w = 28% 20.6
Given H1 = 8.3 m., and H2 = 4.43 m. If the ground water table rises by 2.29 meters, determine the change in effective stress (numerical value only, in kPa) at the bottom of the clay layer. Properties of dry sand: Gs = 2.59, e = 0.61. Properties of clay: Gs = 2.74, e = 0.86. Round off to two decimal places. Answer: 13.95
The water table in an 8 m thick silty sand deposit lies at a depth 3 m below the ground level. The entire soil above the water table is saturated by capillary water and the saturated unit weight is 18.8 kN/m^3 . Calculate the a) total vertical effective stress, b) the porewater pressure, and c) the vertical effective stress at 8 m below the ground level. Express answers in kPa rounded to the first decimal place.
1.A dry sand is known to have an angle of internal friction of 29. A triaxial test is planned, where the confining pressure will be 41 kPa. What is the maximum axial stress, in kPa, (major principal stress) that can be applied? Calculate the value to 1 decimal place. Do not provide units in your answer. 2.A clay soil is subjected to a triaxial test under unconsolidated-undrained conditions. At failure, the major and minor principal stresses are 8401 psf and 4875 psf, respectively. What is the shear strength of this soil if the confining pressure is doubled? Provide your answer in psf with no decimals.
Question 1: (10) For the soil profile shown below where H1 = 5 m and H2 = 5 m: a) Calculate the total stress (o), pore water pressure (u), and effective stress (o') at point A. b) In order to decrease the effective stress at point A by 15 kN/m2, what would be the depth of the water table from the ground surface. XXXX H1 Dry Sand e = 0.60 G, = 2.68 Clay H2 e 0.80 G = 2.75 %3D %23
Solve the following problems using the figure. 1. Calculate the ultimate settlement of the clay layer. 2. Calculate the excess pore pressure (ue) and the effective stress at the midpoint of the clay layer after 3 years. 10' Fill, y = 118b/³ Sand, y 109 lb/ft³ Sand, Ysat 114 lb/ft³ eo = 1.1 Cc = 0.25 C₁ = 7 ft²/yr C₁ = 0.06 clay 14' N.C Ysat = 122 lb/ft³ sand 8. For the previous problem, report the predicted settlement after 365 days. 3. Create a plot (or plots) in a spreadsheet showing the hydrostatic pressure in the clay with depth and the excess pore pressure (ue) with depth after 3 years and the combined pore pressure after 3 years. (This is similar to an example worked in class) 4. Calculate the average percentage of consolidation (U%) for the clay layer after 3 years. 5. How long will it take for 80% of the ultimate settlement of the clay layer to take place? 6. Assume thin layers of drainable sand are present every two feet within the clay so it is actually five clay layers that…
IV. A soil element is shown in Figure 3. (use equations) 130 kN/m² +35kN/m² 30⁰ 60 kN/m² 10 11. 12 + + B SITY FICAT 35 kN/m² Figure 3 What is the value of the maximum stress in kPa? What is the value of the normal stress acting at the plane AB in kPa? What is the value of the shear stress acting at the plane AB in kPa?
At what depth would total the vertical stress in a deep deposit of clay (e = 1.1, Gs = 2.74) be 100 kPa if the water table is 1 m below the ground surface and the above the water surface a saturation degree of 70 % exists. What is the effective stress at the same depth?
A consolidated-drained tri-axial test was conducted on a normally consolidated clay. The results are as follows: O3 = 150 kN/m? (Aoa)f= 130 kN/m? Determine a. Angle of friction, o' b. Angle 0 that the failure plane makes with the major principal plane c. Find the normal stress o' and the shear stress tf on the failure plane d. Determine the effective normal stress on the plane of maximum shear stress
A clay specimen with drained shear strength parameters of c'=5 kPa and Φ=320 is consolidated under all around pressure of 140 kPa.The specimen was then loaded axially to failure under undrained condition and failed when the principal stress diffrences reached 60 kPa.Calculate the pore pressure(u) and the pore pressure coefficient D(=A*B=Δu/Δσv) of the clay.
The saturated unit weight of a 10 m thick clay layer is 20 kN/m3. Calculate the vertical effective stress at a depth of 5 m if the groundwater level is at the surface and select the correct answer from the below: O A. Total stress = 50 kPa Porewater pressure = 48.5 kPa Effective stress = 52.1 kPa O B. Total stress = 120 kPa Porewater pressure = 40 kPa Effective stress = 60 kPa O C. Total stress = 100 kPa Porewater pressure = 49.1 kPa Effective stress = 50.1 Pa O D. Total stress 110 kPa Porewater pressure = 42.2 kPa Effective stress = 55 kPa
The soil profile for a proposed construction site is shown below. The groundwater table is located 2 m below the ground surface. Assume geostatic conditions and ignore any negative pore-water pressures due to capillary rise. (a) What is the effective stress (kPa) at point A? The unit weight of sand is 18.16 kN/m³. (b) What is the effective stress (kPa) at point B? (c) Ten years from now, the depth of the groundwater table will change, resulting in a new effective stress at point B of 72.6 kPa. Based on this information, how far below the ground surface will the new location of the groundwater table be? Ground surface Yt = 13.2 kN/m3 Sand Ysat = ? G3 = 2.70 n = 0.5 A Clay Ysat = 19.6 kN/m3 4 m·