At a point on the free surface of a stressed body, a normal stress magnitude of S, = 63 MPa (C) and an unknown posit exist on a horizontal plane. One principal stress at the point is 9 MPa (C). The absolute maximum shear stress at the p magnitude of 81 MPa. Determine the unknown stresses on the horizontal and vertical planes and the unknown prino point. Sxy Answers: O, = MPa MPa Try =

At a point on the free surface of a stressed body, a normal stress magnitude of S, = 63 MPa (C) and an unknown posit exist on a horizontal plane. One principal stress at the point is 9 MPa (C). The absolute maximum shear stress at the p magnitude of 81 MPa. Determine the unknown stresses on the horizontal and vertical planes and the unknown prino point. Sxy Answers: O, = MPa MPa Try =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bar of a uniform cross-section is rigidly fixed at one end and loaded by an off-centre tensile point load F = 1.5 kN at the other end, see Fig. Q1a. The Figure Q1b presents the view of the beam from the free end where the point of application of the load F is indicated as A. The allowable stress [0]=234 MPa The geometrical parameters are given as follow h 18 mm, b=37 mm N y b Figure Q1a Figure Q1b h F X
At a point on the free surface of a stressed body, a normal stress magnitude of S, = 51 MPa (C) and an unknown positive shear stress exist on a horizontal plane. One principal stress at the point is 11 MPa (C). The absolute maximum shear stress at the point has a magnitude of 64 MPa. Determine the unknown stresses on the horizontal and vertical planes and the unknown principal stress at the point. Sgy S Answers: O, = i MPa i MPa Txy = MPa Op2 =
At a point in a stressed material, the major principal stress is 66 kPa compression and the minor principal stress is 34 kPa tension. (a) Use the Mohr’s circle to determine the shear and normal stress on a plane 45° ccw from the major principal plane. (b) Determine the stress combination acting on the plane 75° ccw from the major principal plane.
For the state of plane stress shown, determine (a) the largest value of o, for which the maximum in-plane shear stress is equal to or less than 20 ksi. (b) the corresponding principal stresses. Assume stress magnitudes of S,- 31 ksi and Sy- 14 ksi. Answers: ksi (a) o, = ksi (b) opl = ksi
I need the answer as soon as possible
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2700 psi, op2 = -2470 psi, Op3 = 0 (b) op1 = 44 MPa, op2 = 25 MPa, op3 = 0
If the principal stresses in a plane stress problem, are σ₁ = 100 MPa, 02 = 40 MPa, the magnitude of the maximum shear stress (in MPa) will be
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2320 psi, op2 = -1590 psi, op3 = 0 (b) op1 = 47 MPa, Op2 = 27 MPa, Op3 = 0 %3D Answer: (a) Tabs max psi MPa (b) Tabs max
Solve alll subparts b, c, d and e B) determine the principal plane (for σmax) in radians. C) Determine the shearing stress in a plane, which is 330 with the vertical (clockwise). D) determine the normal stress (in MPa) in a plane, which is 330 with the vertical (clockwise). E) determine the minimum values of θ (in radians) for which the normal stress is the equal to or less than 35.2 MPa.
If the principal stresses in a plane stress problem, are 0₁ = 100 MPa, 02 = 40 MPa, 01 the magnitude of the maximum shear stress (in MPa) will be
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy-17 MPa, S, - 60 MPa, and Swy- 29 MPa. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses (ơp > op2) and the maximum in-plane shear stress Tmax acting at the point. (c) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g, see Figure 12.15 or Figure 12.16) Say Answers: MPa. Opl = MPa. MPa. Tmax = 0, =
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12.4 ksi, Sy = 3.5 ksi, and Sxy = 3.6 ksi. Assume β=29∘. Determine the normal stresses σx and σy and the shear stress τxy at the point.