At a certain pair in a reaction turbine, the steam eaves the fixed blade at a pressure of 3 bar with a dryness fraction of 0.98 and a velocity of 130 m/sec. The ratio of axial velocity of 130 m/sec. The blades are 20mm high and discharge angle For both the rings is 20°. The ratio of axial velocit of flow to the blade velocity is 0.7 at inlet and 0.76 at exit from the moving blade. If the turbine uses 4 kg of steam per second with 5% tip eakage. Find the mean blade diameter and the power developed in the ring.

At a certain pair in a reaction turbine, the steam eaves the fixed blade at a pressure of 3 bar with a dryness fraction of 0.98 and a velocity of 130 m/sec. The ratio of axial velocity of 130 m/sec. The blades are 20mm high and discharge angle For both the rings is 20°. The ratio of axial velocit of flow to the blade velocity is 0.7 at inlet and 0.76 at exit from the moving blade. If the turbine uses 4 kg of steam per second with 5% tip eakage. Find the mean blade diameter and the power developed in the ring.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a stage of Parson's reaction turbine, the mean diameter of the wheel is 1.05 m and the speed is 3000 r.p.m. The angles of receiving tips are 35° and the discharging tips is 20°. If the steam flow rate is 1 kg/min, draw the velocity diagram for blades and evaluate, (a) Tangential thrust on blades (b) Axial thrust on blades (c) Power developed in the blades and (d) Diagram efficiency.
Derive the equation for turbine and nozzle with the help of steady energy equation by stating their assumptions.
Inner and outer diameters of an outward flow reaction turbine wheel are 1m and 2m respectively. The water enters the vane at angle of 20° and leaves the vane radially. Assuming the velocity of flow remains constant at 12m/s and wheel rotates at 290rpm, find the vane angles at inlet and outlet. Show schematic diagram and provide solutions.
A rection turbine has guide vane angle 30° the runner blades make an angle of 80° relative to the tanget at inlet .the blades width at inlet is 1/4 of the outer diameter .the water does not have any tanget velocity at outlet.the head is 25 m and the rotational speed of the runner is 16.67 rotation per second (rps) the turbine efficiency is 88% determine the runner diameter at the inlet and the power developed by this turbine
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
Q . It is proposed to pump 8,000 kg/h of toluene at 114 oC and 1.1 atm abs pressure from the reboilerof a distillation tower to a second distillation unit without cooling the toluene before it enters thepump. If the friction loss in the line between the reboiler and pump is 7 kN/m2 and the density oftoluene is 866 kg/m3 . How far above the pump must the liquid level in the reboiler be maintained togive a net positive suction head of 3.5 m? Calculate the power required to drive the pump if the pumpis to elevate the toluene 10 m. The pressure in the second unit is atmospheric and the friction loss inthe discharge line is 35 kN/m2 . The velocity in the pump discharge line is 4 m/s.
In a reaction stage of a stcam turbine the nozzle angle is 20° and the absolute velocity the steam at inlet to the moving blades is 240 m/s. The blade velocity is 210 m/s. If 1.7 the blading is designed for 50% reaction, determine: (i) the blade angle at inlet and exit; il the cathalpy drop per unit mass of steam in the moving blades and in the complete stage; (i) the diagram power for a steam flow of 1 kg/s: (iv) the diagram efficiency. (79.3, 20°; 25.3 kJ/kg; 50.6 kJ/kg; 50.6 kW; 93.5%)
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour
QUESTION 3 A high-pressure axial compressor for a stagnation pressure ratio of 8.5. The mass flow rate of air through the compressor is 16 kg/s and the stagnation conditions at inlet are 200 kPa and 450 K. The polytropic efficiency is 91 %. jet engine rotates at 15,000 rpm with and overall (a) If the mean radius is 0.24 m and this is constant throughout the compressor, calculate the total-to-total isentropic efficiency of the compressor and show that, for the stage loading to be less than 0.4 in all stages, eight stages required. are (b) The compressor is designed with repeating stages and zero inlet swirl. If the inlet axial Mach number is 0.52, calculate the mean flow coefficient and sketch the velocity triangles for one stage. Show that the blade height at exit from the compressor is about 7.8 mm.
The rotational speed of an impulse turbine is 3000 rpm and the mean diameterof the rotor is 90 cm. Given that the utilization factor is 0.9, find the inlet bladeangle and power output if the mass flow rate is 2.5 kg/s. The inlet to the turbineis through a nozzle that makes an angle of 22° with the blade tangent. The inletfluid velocity is 250 m/s.Ans: β1=46.0°; P=70.3 kW
A blade pair in an axial flow compressor is being designed. The axial flow component of gas velocity is 174m/s. The engine diameter at the mean blade height is 0.73m and the blade height at the rotor inlet is 0.21m. The rotor's absolute inlet flow angle is 26 degrees. The stagnation conditions at the inlet to the blade pair are 298K and 130kN/m² Using Cp 1.005k/kg/K, R-0.287k/kg/K, and taking the ratio of specific heat capacities as 1.4, calculate the engine mass flow rate to the nearest kg/s
The centrifugal compressor of a gas turbine receives air at 1bar and 300K. At the discharge ofcompressor, the pressure is 4bar, temperature is 480K and velocity is 100m/s. The mass rate of flowinto the compressor is 15kg/s. Determine the power required to drive the compressor.