ASteel bar of (25mm) diameter was tested in tension and results were recorded as Load at Yield 218.13KN,Ultimate load (278.2KN).The Elongation measured over gauge length of (100mm) was ( 12.62mm)at Fracture point and minimum diameter was (23.64mm) determine Yield stress,Ultimate stress,%Elongation, * %rudection in area ث إضافة ملف

ASteel bar of (25mm) diameter was tested in tension and results were recorded as Load at Yield 218.13KN,Ultimate load (278.2KN).The Elongation measured over gauge length of (100mm) was ( 12.62mm)at Fracture point and minimum diameter was (23.64mm) determine Yield stress,Ultimate stress,%Elongation, * %rudection in area ث إضافة ملف

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tension test was conducted for a cylindrical specimen of stain-less steel having an initial diameter (D) of 10.85 mm. Calculate the percentage reduction in area if the fracture diameter of the specimen (d) is 6.15 mm. Select one: O a. 68.87% O b. 69.87% c. 66.87% O d. 67.87%
Find the area, yield point, and the rest of the problem.
Required information A shaft is loaded in bending and torsion such that M₂ = 66 N-m, T₂ = 42.496 N-m, Mm = 51.858 N-m, and Tm - 33 N-m. For the shaft, Su = 700 MPa and Sy=560 MPa, the true fracture strength is 1045 MPa, and a fully corrected endurance limit of S₂ = 210 MPa is assumed. Let Kf= 2.2 and Kfs=1.8. With a design factor of 2.0, determine the minimum acceptable diameter of the shaft using the methods mentioned in the subsection. Determine the minimum acceptable diameter of the shaft using the DE-Morrow criterion. The diameter of the shaft is mm.
Required information A shaft is loaded in bending and torsion such that Ma= 66 Nm, Ta=42.496 N.m, Mm = 51.858 N.m, and Tm = 33 N-m. For the shaft, Su = 700 MPa and Sy=560 MPa, the true fracture strength is 1045 MPa, and a fully corrected endurance limit of Se = 210 MPa is assumed. Let Kf= 2.2 and Kfs=1.8. With a design factor of 2.0, determine the minimum acceptable diameter of the shaft using the methods mentioned in the subsection. Determine the minimum acceptable diameter of the shaft using the DE-Morrow criterion. The diameter of the shaft is 27.16 mm.
The total load for a canopy overhang is 105,340# and the load is equally distributed to five steel rod ties. The sample steel rod tested has tensile strength of 20,000psi. A selection of steel rods (same material as the tested sample) is available in different sizes shown below. Select the rod size that best fits this application? (SA = Surface Area) (f= P/A) (LO4) O 1" (SA= 0.79 sq in) 3/4" (SA=0.44 sq in) O½" (SA= 0.20 sq in) O 1¼" (SA= 1.22 sq in) O 1½ (SA= 1.76 sq in)
3. A rod-shaped MgO specimen with round cross section is tested with the three-point bend method. What is the calculated minimum radius without fracture if the applied load is 5560 N, the flexural strength is 105 MPa, and the separation between the two support pins is 45 mm?
A bar made of carbon-steel of size 12mm x 20mm has a yield stress of 400 MPa and ultimate tensile strength of550 MPa. Tha gauge length of the specimen tested under tension loading is 350mm. a. Determine its elongation when a tension load of 75 KN is applied. b. Determine the maximum load the bar can take before it fractures. Take Youngs Modulus of steel as 200,000 MPa
A tensile-testing apparatus is to be constructed that must withstand a maximum load of 293516 N. The design calls for two cylindrical support posts, each of which is to support half of the maximum load. Furthermore, plain-carbon(1045) steel ground and polished shafting rounds are to be used; the minimum yield and tensile strengths of this alloy are 343 MPa and 565 MPa(82,000 psi), respectively. Specify a suitable diameter in mm for these support posts. Assume safety level is 2.3. Round your answer to 2 significant figures.
9:17 A Mild steel specimen of circular cross-section is subjected to tensile test with following data ultimate load of 235 kN, final area - 499 mm?, initial area - 672.8 mm?, final length - 387 mm, initial length - 299 mm. Find the Initial Diameter, % of Elongation in length, % of Reduction in area & Ultimate strength. 3 Marks)
In a bending test for a brittle material, the distance between the supports is 300mm, the cross sectional area of the specimen is 1200 and the thickness is 30mm. find the transverse rupture strength if the applied load was 1 ton.
P
Sketch the stress / strain relationship for steel bar element