Assume we are using a microcontroller that is only compatiable with the C language. Given an input of some AC sinusoidal voltage wave, create a function to calculate the frequency of the input wave if the internal instruction clock is running at a frequency of 1 Mhz. Assume we have a function called "Volts()" with void parameter that returns the voltage that is read by the microcontroller at that specific time.

Assume we are using a microcontroller that is only compatiable with the C language. Given an input of some AC sinusoidal voltage wave, create a function to calculate the frequency of the input wave if the internal instruction clock is running at a frequency of 1 Mhz. Assume we have a function called "Volts()" with void parameter that returns the voltage that is read by the microcontroller at that specific time.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 30RQ

See similar textbooks

Similar questions

List the pins on Arduino that can do analog write. In a PWM, given that the duty cycle is 80% what is the voltage output? In a PWM, what should be the duty cycle to get a voltage output of 4.5 V? Given the bellow Arduino command: analogWrite( 8, 200); What is the duty cycle? What is the voltage output?
Can you draw the circuit for this ? Thank you ?
3. Graphical Representation of the signal 1) Write the type of the voltage from simulation results: 2) Write the value of the voltage from simulation result: L....... -2 DDU 12ns SónG Trace Color Trace Name X Values CURSOR 1,2 V(R1:1,0) Y1 Y2 Y1 - Y2 5.0373m 0.000 5.0373m 249.983 0.000 249.983 Y1(Cursor1) - Y2(Cursor2) Y1-Y1(Cursor1) Y2 - Y2(Cursor2) Max Y Min Y Avg Y 249.983 0.000 0.000 249.983 0.000 124.991
What is the problem of using a pushbutton or a switch as a digital input to a microcontroller. Then, what is the solution(s) of that problem?
Explain concisely and in your own words the procedure to be carried out for: Vacuum test and Short-circuit test
1. For the ADC0804 used in section 1. the step size can be adjusted by setting the reference voltage on pin 9. When this pin is not connected (as shown in the figure 1 schematic), the reference voltage is the operating voltage Vcc. a) What is the step size for this default setting? b) How can we set the reference voltage on pin 9. to 4 V? c) What would be the step size after changing the reference voltage to 4 V? 2. Determine the analog input that will result in an output code of "10001110". Assume 5 V reference. Show your calculations. 3. What value of the analog input voltage would result in a digital output is 6F (hex)? Assume 4V reference. Show calculations. 4. In section, you used a 8-bit D/A converter. With a reference voltage of 5 V, what voltage does each bit represent in terms of the analog output? Show calculations. 5. For the D/A converter, if the output is 3.62 V, what is the value of the digital input? Show calculations. 6. For the D/A converter circuit shown in Figure 2,…
Describe the purpose of a PV and PQ curves. Draw the curves and explain its position (stability & unstable areas) Describe the difference between each curve by reference to the curves and explain when each one would be used
help me in these questions pls write the questions with the and by (Computer)1- Explain how the circuit below works to perform its main function?i. Zener diode is short circuited when voltage across it rises beyond its breakdown voltage.ii. Radiation from light emitting diode is detected by a phototransistor without having any physical contact.iii. The circuit prevents the LED from having the wrong polarity or too high voltage.iv. The circuit prevents the alternating signals by rectifying it using a diode. a. All the answers. b. i, ii and iii only. c. i, iii and iv only. d. i, ii and iv only.========2- Which of the following statement is most probably INCORRECT in explaining the working principle of an engine management system? a. Microprocessor is used to process incoming signal including position, speed, timing, flow, and temperature. b. The operation of valves and spark ignition is in sequence following the stroke action. c. The timing of the sequence is fixed.…
Explain the process of manufacturing microchips. What materials and techniques are involved in producing integrated circuits?
The circuit that converts ac to dc is called a. Attenuator b. Rectifier c. Inverter d. Amplifier
An analog signal varying between 1V and 3V will be converted to digital and the signal voltage value will be displayed on the LCD screen. The signal to be measured will be between 1V and 3V. 3 analog signals will be read using the AN5, AN6 and AN7 pins. Values in these signals will be displayed one by one on the LCD screen as digital and voltage values. Draw the circuit diagram and write the PIC C codes.
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.