Assume that the inductor is fully discharged when the switch is closed. Important: Enter your answers WITHOUT units, for example if your answer is 0.0028 meters you must enter 0.0028 The RL circuit is connected to a 24 volt battery, where R = 100 and L=2H Calculate the time constant of the inductor. TL How long does it take to charge the inductor? t = Write the algebraic expression for the inductor current as a function of time. IL= What is the voltage of the inductor when it is loaded? VL = V What is the current of the inductor when it is loaded? IL= A t= Calculate the time it takes for the inductor current to go from 0 Amps to 1.2 Amps. S Vs Example: -9+exp(-5*t) R.

Assume that the inductor is fully discharged when the switch is closed. Important: Enter your answers WITHOUT units, for example if your answer is 0.0028 meters you must enter 0.0028 The RL circuit is connected to a 24 volt battery, where R = 100 and L=2H Calculate the time constant of the inductor. TL How long does it take to charge the inductor? t = Write the algebraic expression for the inductor current as a function of time. IL= What is the voltage of the inductor when it is loaded? VL = V What is the current of the inductor when it is loaded? IL= A t= Calculate the time it takes for the inductor current to go from 0 Amps to 1.2 Amps. S Vs Example: -9+exp(-5*t) R.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PA: You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor...

See similar textbooks

Similar questions

You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
Can current flow through a capacitor?
4. In what form is the energy of a capacitor stored?
What is the value of the induced voltage of the self-inductance when the rate of current is from 200 uA to 20 uA and the total time interval is 5 uS?
The switch (SW) in the circuit is opened for a long time shown Figure 2. A. Calculate the expression of the current of inductor. B. find the value of the current of inductor at t-20 msec. 30 20 10 sa Figure 2
A supercapacitor is an electrical energy storage device. A supercapacitor, initially charged to 9.8 thousand millivolts, supplies power to an emergency beacon. The power draw from the load causes the capacitor to lose 4.4% of its charge every minute. When the charge drops below 7 hundred millivolts the beacon will cease functioning. How long will the beacon last after it is activated (your final answer should be in minutes). Round your answer to the nearest minute.
C) A 25 A electrodynamic ammeter is controlled by a spring having a constant of 5.7295x 10-6 Nm/rad. The full scale deflection is 110°. Determine the inductance of the instrument while measuring a current of 20 A. The mutual inductance at 0° deflection is 4 u H and the change in mutual inductance is linear with the deflection.
Find the current through the inductor shown in Figure lb. (i/p is AC, consider results upto one decimal place). 1. 100 V 100 Hz 500 L=60H Figure lb
An uncharged capacitor and bulb are connected in series with a battery. Describe and explain what happens to thebulb when the switch is closed. What determines when the capacitor stops charging? What happens if the capacitoris turned around after the switch has been closed a long time? Include where charge is flowing the circuit. Alsodescribe the different roles of the capacitor and the battery.
The figure displays two circuits with a charged capacitor that is to be discharged through a resistor when a switch is closed. In figure (a) below, R₁ = 23.32 and C₁ = 5.04 μF. In figure (b) below, R2 = 10.82 and C₂ = 8.10 μF. The ratio of the initial charges on the two capacitors is 902/901 = 1.61. At time t = 0, both switches are closed. At what time t do the two capacitors have the same charge? 0.0 (a) (b) Number i Units
An inductor is constructed by winding a coil of 100 turns around a magnetic core. The core is a cylinder with radius 0.5 cm and the core material has relative permeability of 1000. The coil covers a length of 10 cm. Determine the resulting inductance. Enter your answer in mH rounded to two decimal places.