As per the shortest processing time' crite- rion, the average number of jobs in the system is (A) 3.4 (B) 3.2 Arranging according to SPT, (C) 2.6 (D) 1.8. Job Processing Flow Due Job time time date lateness 25 01 11 40 18 20 27 16 11 11 38 15 23 38 99 34 5. 2.

Q: How does Impulsive forces occur?

A: Impulsive force:- When a force acted on a body for short period of time then it is called impulsive…

Q: Define the term form factor?

A: Generally, the word Form factor is defined for the surface finish and tolerance provided over any…

Q: What is known as extensive quantities ?

A: Extensive properties are those properties that depend upon the mass of the system. The energy…

Q: t is the figure called? explain and elaborate

A: The apparatus is a open cup flash point test apparatus

Q: All physical quantities involve a direction

A: Given Physical quantity To find Direction based physical quantity

Q: would it be possible to get a detailed explanation? thank you

A:

Q: For the process shown in the schematic below, which of the statements is/are incorrect? Feed hopper…

A: 1)b. The process can only work with thermoplastics and not with thermosets due to the thermal…

Q: 1- A simple introduction. 2- The benefits of this process. 3- The disadvantages of this process. 4-…

A: The mechanical motion of a punch is used to deep draw sheet metal. Under consistent hydrostatic…

Q: can I have FBD for this?

A:

Q: Which of the following is NOT TRUE with respect to the Elastic Transverse Shear Formula?…

A:

Q: If a car weighing 2400 lbs is able to go 1000 ft up a mountain incline whose angle of inclination is…

A: Given data: Weight of car = 2400 lbs                      Distance which car moves up the incline =…

Q: 180 200 30 Find F and Lacation 令 ocation 200

A:

Q: Stanum is vital as mankind enters Stone age New age Brass age Bronze age

A: Correct answer: Bronze age

Q: Hi, please complete the last three subparts of this question.

A: To calculate the rate of heat transfer, to derive and to calculate the mass flow rate of water, flow…

Q: Define the Temperature Scales?

A:

Q: It causes resistance due to applied forces which is a result of restrain deformations   Shear Force…

A:

Q: Water flows from a large tank into a 6" diameter pipe through an entrance condition of a square…

A: Given:Pipe diameter, D2=6 inchRadius of the rounded inlet, r=0.12 inchFind:The head loss reduced at…

Q: Name the views that are used to show the part.

A: Engineering drawing is an arrangement of different drawings of a single object viewed from the…

Q: Is this the only correct option in the question above? I think the question is worded for more than…

A: To elaborate why a sling psychrometer can measure humidity.

Q: How forces are transmitted?

A:

Q: Hi could you also please give the solution to d, e, f

A: As per the guidelines we are subjected to solve only 3 sub parts at a time. Please repost the same…

Q: Figure A. Rectangular block of steel. Adapted from: https://media.wdscomponents.com/ri-…

A: Given: Workpiece is slimmed using slab milling To find: 4 items need to perform slab milling process

Q: Can you please answer the rest of the subpart? Thank you!

A:

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the state…

A:

Q: A package of frozen fish sticks have different instructions when they are heated up on the stove as…

A:

Q: What's the worst car ever made?

A: Given Data⇒ worst car Problem statement⇒ Problem says What's the worst car ever made?

Q: Describe the work done is proportional to the force applied (F ) and the distance traveled (s).

A: We know that,Work Done =Force × DisplacementW = F × s From the above equation, If…

Q: "If we push the book on the table, it stops after sometime. Why?"

A: If we push the book on the table, then the book will get some speed. but after some time the book…

Q: Hello, sorry for not clarifying which parts to solve, could you please do part D?

A: Given data:- The speed of the impact is doubled To find:-the maximum compression of the spring

Q: It is a water pressure copper pipe, household tap water coming out. Identify a copper pipe material…

A: Material: Copper (Specifically, type L copper)Justification: Type L copper is commonly used for…

Q: Using scientific methods, how would you know the right temperature and heat needed to bake to right…

A: Following steps can be used - With the help of protein denaturation temperature, we can know the…

Q: Explain three pages of laminar flow with the drawing

A:

Q: give a steps by steps explanation of the solution

A:

Q: The following data are available from orthogonal cutting experimental. In this case: Thermal…

A: Solution:

Q: ACCURATELY

A: We have given ACCURATELY

Q: A manufacturing company has an order for a specific new product. The order quantity is 45,000 units.…

A:

Q: Problem 3: A small gearing system in your brand-new 3D printer fails as you were printing, leading…

A: To prove: We must demonstrate that the equipment failed under normal operating circumstances in…

Q: horwalizing 1) Machinability of low carbon steels improved by: high carbon steel improved by…

A: Heat treatment processes are used to get the desired properties in the metals.

Q: Manufacuring Processes An electro chemical machining (ECM) operation is employed too cut a square…

A: Write the given data:

Q: why is the length of the wire use in finding the centripetal force instead of the radius?

A:

Q: Q2: Select any one casted component shown in the figure which is made up of alloy material and used…

A: I will select second one i.e  spiral bevel gear. Alloys used in making gears is zinc alloys  or…