As part of an engineering design, a load of mass M2=10 kg is to be suspended from the far end of a beam of mass M1=8kg. A horizontal cable supporting the beam attaches to the beam at a distance of d=2m from a joint/hinge. The length of the beam is L=7m. The beam makes an angle of 55 degrees with the horizontal.

As part of an engineering design, a load of mass M2=10 kg is to be suspended from the far end of a beam of mass M1=8kg. A horizontal cable supporting the beam attaches to the beam at a distance of d=2m from a joint/hinge. The length of the beam is L=7m. The beam makes an angle of 55 degrees with the horizontal.

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 32P

See similar textbooks

Similar questions

A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
A 20.0-kg horizontal plank 4.00 in long rests on two supports, one at the left end and a second 1.00 m from the right end. What is the magnitude of the force exerted on the plank by the support near the right end? (a) 32.0 N (b) 45.2 N (c) 112 N (d) 131 N (e) 98.2 N
A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
One end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an angle of ? = 37.0°above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable.
A beam held by a hinge, take 2. The left end of a beam of mass 17.9 kg is fixed to a wall by a hinge. The beam is inclined at 19.8 degrees from the horizontal; it is supported at its right end by a rope forming an angle of 30.3 kg with the horizontal.create a model for the orientation of the hinge force, relative to the x+ axis.
A 3 m long weightless beam is supported at each end by cables. A painter weighing 900 N stands 1 m from the left cable. Calculate the tension in each cable.
A beam with length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board. Suppose the maximum tension that the wire can withstand is 1500 N. What is the maximum load that the hinge can support before the wire breaks?
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
A beam with a length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board
In the figure, a uniform beam of weight 440 N and length 2.3 m is suspended horizontally. On the left it is hinged to a wall; on the right it is supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1100 N. What value of D corresponds to that tension? Cable Вeam Number i Units
A 15.7 m long board is supported from beneath at two locations. One is at the far left end of the board. The other is 1.2 m from the right end of the board. The board has a mass of 39.7 kg. What is the normal force (in newtons) applied by the right support?
In the figure below, a uniform beam of weight 420 N and length 2.8 m is suspended horizontally. On the left it is hinged to a wall; on the right is it supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1200 N. Cable Beam (a) What value of D corresponds to that tension? (b) Give any value for D that won't snap the cable. m