As communication engineer you are requested to design a radio communication system using parabolic dish antenna of 120 cm diameter, for 1800 MHz. Assume the input power is 1 KW, radiated power is 62-W and radiation resistance is 18.750 for the antenna. For this antenna system, find: Efficiency of the antenna; ii. i. Gain of the antenna; ii. The Loss resistance

As communication engineer you are requested to design a radio communication system using parabolic dish antenna of 120 cm diameter, for 1800 MHz. Assume the input power is 1 KW, radiated power is 62-W and radiation resistance is 18.750 for the antenna. For this antenna system, find: Efficiency of the antenna; ii. i. Gain of the antenna; ii. The Loss resistance

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

15. _______ is a proximity sensor that uses the principle of ‘eddy current’ to sense the presence of an object.
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
I need the answer as soon as possible
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…
Select the best answer from multiple choices: 1. The system e'e-5 is: a. Linear, time invariant, casual. b. Non-linear, time invariant, non-casual. c. Non-linear, time varying, casual. d. Not all the above. 2. Noise can be reduced through: a. Increasing So. b. Increasing Si. c. Both (a) and (b). d. Note all the above.
I have the answers fro my textbook they are not matching with the one that you send
Get the same shape required and Give proper label and title by using OCTAVE and write the program
Why did not I find your solution to all my questions ?
I want to solve both questions please
Grateful some help with this question thanks.