As a Network Engineer, assume that you are given 9 input-lines that carry digital inputs, and the rates of these 9 lines are as follows: • 5 lines with a data rate of 6O0Bps (each), • 2 lines with a data rate of 200Bps (each), • 2 lines with a data rate of 100Bps (each). Now, to multiplex such digital input lines using an efficient synchronous multiplexing scheme with no synchronization bits, if 96 bits are multiplexed at a time, find the following: (1) The link data rate equals bps. Note: Please add your answer using numbers ONLY with NO spaces, using 3 digits of accuracy when needed.

As a Network Engineer, assume that you are given 9 input-lines that carry digital inputs, and the rates of these 9 lines are as follows: • 5 lines with a data rate of 6O0Bps (each), • 2 lines with a data rate of 200Bps (each), • 2 lines with a data rate of 100Bps (each). Now, to multiplex such digital input lines using an efficient synchronous multiplexing scheme with no synchronization bits, if 96 bits are multiplexed at a time, find the following: (1) The link data rate equals bps. Note: Please add your answer using numbers ONLY with NO spaces, using 3 digits of accuracy when needed.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 2PE

See similar textbooks

Similar questions

Your company has a video transcoder. Each network interface returns the number of transmitted and received octets at a precise moment. The bitrates need to be added to the transcoder. Calculate the needed bitrates for receiving (Rx) and transmitting (Tx) considering a pooling rate of 4Hz. Tx: 289652580 Rx: 6488574452
Suppose, you have 6 voice channels, each of 60MBPS. You have to use synchronous TDM to multiplex these channels. If 2 characters at a time are multiplexed (2 characters in each output slot), answer the following: What is the size of an output frame in bits? What is the output frame rate? What is the duration of an output frame? What is the output data rate? Input bit duration? Output bit duration? Output slot duration?
III. The figure below shows synchronous TDM, the data rate for each input connection is 1 Mbps. If 1 bit at a time is multiplexed, Find (a) the input bit duration, (b) the output bit duration, (c) the output bit rate, and (d) the output frame rate. ... 1 1 1 1 1 1 Mbps 0 0 0 0 0 1 Mbps Frames 01010001110100010101 ... MUX 1 0 1 0 1 1 Mbps *** 0 0 1 0 0 1 Mbps
A line has a signal-to-noise ratio of 1000 and a bandwidth of 4000 kHz. What is the maximum data rate supported by this line? If the bandwidth of the channel is 5 kbps, how long does it take to send a frame of 100,000 bits out of this device? What is the maximum data rate of a channel with a bandwidth of 200 kHz if we use four levels of digital signaling?
Four channels are multiplexed using synchronous TDM. The rate of each channel is given by 500 kbps and we use 2-bit units, provide a step-by-step calculation for the following: 1. Input bit duration 2. Input unit rate 3. Output frame rate 4. Output frame size
2. A path in a digital circuit-switched network has a data rate of 1 Mbps. The exchange of 1000 bits is required for the setup and teardown phases. The distance between two parties is 5000 km. Answer the following questions if the propagation speed is 2 X 10° m: a. What is the total delay if 1000 bits of data are exchanged during the data transfer phase? b. What is the total delay if 100,000 bits of data are exchanged during the data transfer phase? c. What is the total delay if 1,000,000 bits of data are exchanged during the data transfer phase? d. Find the delay per 1000 bits of data for each of the above cases and compare them. What can you infer?
We need to use Synchronous Time Division Multiplexing to combine 17 different channels, where 10 channels are each of 300 Kbps and 7 channels are each of 600 Kbps. A unit is 1 bit. Now, answer the following questions using multilevel TDM with no synchronization bit. Your answers must have units. i) What is the output bit duration? ii) What is the size of an output frame in bits? iii) What is the input bit duration?
3 A 100MB of data is required to be transferred from STATION-A to STATION-B. The are used to setup a point-to-point circuit from station A to station B as shown in the figure distance between the two stations is 10000Km. There are two intermediate switches which below. 3000Km Switch 1 A Switch 2 STATION-A Considering the speed of the propagating a time of the first and last bit at station B. 3000K STATION- signal as 2*10^8 m/sec, calculate the arrival 10
Calculate the minimum timeout value for a stop-and-wait algorithm running over a 50-meter point-to-point copper link. Assume a minimum delay of 5 µs at the receiver. If you know the distance between two points, you can calculate the speed-of-light latency, although you have to be careful because light travels across different media at different speeds: It travels at 3.0 × 108 m/s in a vacuum, 2.3 × 108 m/s in a copper cable, and 2.0 × 108 m/s in an optical fiber.
if you are given alow-pass channel that ends at 40MHz and you knew that the SNR for this channel is 255, then the maximum number of signal levels to be used over this particular channel equal?
4. Suppose two users in a Direct Sequence-CDMA system have signatures (that is, sequences of chips) given by (1 -1 1-1) and (1 1 -1 -1), respectively. (a) Evaluate the correlation between the two signatures. (b) Sketch the baseband signals for the two users when user 1 sends the bits 011, and user 2 sends the bits 101. Add the signals for the first bit only, and show that the output of the correlator for user 1 is -4, and the output of the correlator for user 2 is 4. Note that if the output of the correlator is negative, then the detected bit is a 0, and if the output is positive, the detected bit is a 1.
We need to use Synchronous Time Division Multiplexing to combine 17 different channels, where 10 channels are each of 300 Kbps and 7 channels are each of 600 Kbps. A unit is 1 bit. Now, answer the following questions using multilevel TDM with no synchronization bit. Your answers must have units. i) What is the output frame duration? ii) What is the output frame rate? iii) What is the output bit rate?