Anything AND'ed with its complement will give an output of a.0 b.1 c.Could be 1 or 0 d.This is not a situation that could ever occur

Q: NOTE: THIS IS A ELECTRONICS ENGINEERING SUBJECT

A:

Q: Q OUT CLK

A: STATE TABLE OF D-FLIP FLOP: D(Input) Qn+1(Next sate) 0 0 1 1   CHARACTERISTICS TABLE OF…

Q: Hi i am trying to convert a pwm signal to a ramp signal, i have an output that currently generates…

A: ⁹

Q: Voc빵12V Ic Rc=560ohm R3=100kohms в VCE VBE E B=100

A: Let us assume that transistor operate in active mode  Vbe=0.7 KVL in outer loop  Vcc=IB RB+Vbe…

Q: What are combinational circuits? Draw the classification diagram of them

A: Circuit: A circuit is a fully enclosed circle through which electricity travels. A current source,…

Q: Vi Ru Ri Vz 2. I, R2 = 3837.79 Q. R1 = 3763.67 Q. R3 = 3989.3 Q. R4 = 2898.06 N. V1 = 4.8 V. V2 =…

A: L

Q: Q23. Using the below circuit draw the following waveforms over the period of 4 m if the firi angle…

A: Given thyristor firing angle π which is 180° since thyristor works for postive half cycle with gate…

Q: Calculate the output for the given circuit . R2 R2 R Voa R R1 Let the values are R1=617ohm,R2=807.15…

A:

Q: Connect a thermistor (Resistance=500 – 1% per °C ) in a bridge (power supply =8V) with an…

A: Given:- Rt=500ohmα=1% per°cV=8voutput of inverting amplifier=4v at 30°t= final temperature=30°

Q: 2. a) Draw the output waveform C and D, given the input waveforms A and B as shown below figure 2.…

A: Note :- 2 (b) simulation tool required. As per the guidelines we are instructed to not use any…

Q: slove part C please

A: Fig: Given logic circuit

Q: what is VFD and soft starts and give application example each

A: VFD: A Variable Frequency Drive regulates the frequency of the electrical power supplied to the…

Q: Give the state transition diagram for 2's Complementer. Define MOORE State Machine

A: The state diagram is visual representation of the sequence. It shows the internal states and…

Q: 1. Define line regulation. 2. Define load regulation. 3. The input of a certain regulator increases…

A: As per guidelines given to us we can only provide the solution of first question in multiple type of…

Q: It is the characteristics of a transistor when a positive signal applied to the Base of the…

A: In this question we will write when BJT acts as closed switch...

Q: 1. A voltage regulator with a no-load output dc voltage of 12 V is connected to a load with a…

A: NOTE : As per our company guidelines we are supposed to answer only one question. Kindly re-post the…

Q: answer fastly please 57. Discuss the concept of metastability in digital circuits.

A: Key references:How to Avoid Metastability in Digital Circuits. (n.d.). Resources.pcb.cadence.com.…

Q: NOTE: THIS IS A ELECTRONICS ENGINEERING SUBJECT

A: Rectifier is used convert AC Input to Pulsating DC output  Pulsating DC output is converted to less…

Q: Q1 Analyse the circuit shown in Figure Q1, (а) Name the function of each Op-Amp, A1, A2, A3, and A4…

A:

Q: UE be o V and let VFALSE be -6 v. Let PWM be 0.6 seco What is TON to get an average output of 2.6 V?…

A:

Q: After quantization, the analog signal has Select one: a. finite amplitudes O b. infinite amplitudes…

A: After quantization, the analog signal has  a. finite amplitudes b. infinite amplitudes c. finite…

Q: The following waveforms are measured on the input and output of a rectifier while driving a…

A:

Q: Clock Construct the State Transition Diagram for the following circuit. Please include all steps. 1…

A: Given

Q: Vs, V s(pk), V L(pk), V dc, PIV, dnu Tout• DI aW diSU output waveluim the volldge labeleu. Si ell

A: NP=5NS=1VP=138 Vacfin=57Hz

Q: 3:- Detine 4 only; Error, Passband, Standard, Negative Temperature Coefficient, Dynamic Range 24:-…

A:

Q: Two wires are carrying a measurement signal, one wire is at 10 V and the other wire is at 8 V.a…

A: The circuit for the mentioned condition can be made as: So, the two inputs given are: V1 = 10V V2 =…

Q: based on your understanding on amplifiers and Oscillator, explain the operation of Hartley…

A: As per our policy we can provide solution of only first question. Hartly Oscillator : R1 & R2…

Q: Perform the (v1-v2)/3 operation using an opamp.

A:

Q: Question: Given the circuit illustrated below and different types of input signal. Provide an answer…

A:

Q: Output voltage from the circuit in Figure 1, 2, 3, 4 and 5 please :)

A: Step 1:Step 2:

Q: PLEASE INCLUDE A DETAILED STEPS What are the steps in designing combinational circuits?

A: This question is related to digital circuits.

Q: A diode is ;

A: We know that  A diode is a two terminal unilateral semiconductor device. Unilateral means( A diode…

Q: Q2. The stabilizer current of the thyristor in the circuit is below 100mA and the delay time of the…

A:

Q: Q2 (a) Figure Q1(a) Analogue to Digital Converters (ADCs) are used to change analogue signals to…

A:

Q: . Which of the following conditions limit the alysis of quiscent point (Q-point)? A. The circuit…

A: Quiescent point or Q- point- When a line is drawn joining the saturation and cut off points, such a…

Q: Choose an individual of particular importance in this field of circuits and write a very brief…

A: The explanation of an individual of particular importance in the field of circuits and a brief…

Q: Calculate the output for the given circuit. R2 R2 Vo- ww ww R Veo R1

A:

Q: An analog signal in the range 0 to 12 V is divided into 32 equal intervals using a 5 bit quantizer.…

A: During analog signal to digital signal conversion using a uniform quantizer, step size plays a very…

Q: scribé the function of signal conditioning in this block diagram. 5V 12V hermocouple 50 mV; output…

A: The thermocouple is a perfect example for an analog input device. As the signal conditioning system…

Q: 2. Find the gain and also Vo for the given circuits. Name the circuit. (a) 33.3k2 25mV oM OVo 2.…

A:

Q: The correct name for the the symbol below is A Thyristor फै Select the correct definition for the…

A: Given: options for thyristor definition.we need to select:correct options for thyristor definition.

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.