Answer the problem with complete solution and box the final answer with 4 significant figure and unit. Write on a clean paper clearly. And take a picture, scan it then submit here. Using Nominal Mix Design, calculate the individual quantity of cement, sand, gravel, and waterfor the following structural elements of a given project:1. Column Footings2. Footing Tie Beams (FTB)3. ColumnsBIG4. Roof BeamsGiven:FS = 1.54Pement = 1440 kg/mPaand- 1600 kg/mPgrasel = 1560 kg/m³Water to Cement ratio = 0.5

Answered: Answer the problem with complete…

Answer the problem with complete solution and box the final answer with 4 significant figure and unit. Write on a clean paper clearly. And take a picture, scan it then submit here.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: y 20 mm 30 mm 20 mm 10 mm 40 mm X mm

A: The dimensions of the section are given . The centroid is 34 mm above x - axis .

Q: A wooden buoy (s.g. = 0.62) is 70 mm by 70 mm by 5 m long is made to float in sea water…

Q: The blocks shown in the figure weighs 35 kips. Find the value of x

A: Thw weight of the block is balanced by buoyant force by oil and water.

Q: vide a well detailed solution explaining how to get the missing value (highlighted blue) of…

A: As mass retained on 2.36 is not given let it be 'x' Find total mass retained = 438+x Given total…

Q: A composite section shown in Figure (2) consisted of a rectangular and triangular sections with a…

Q: QUESTION 1. otension =24 MPa, ocompression =30 MPa, M=?

Q: A two pinned end bars AB (Copper), A=850 mm², E = 120 GPa and BC (Aluminum), A= 1000mm², E = 70 GPa…

A: Given: The area of bar AB is 850 mm2. The modulus of elasticity of copper is 120 GPa. The area of…

Q: For the cross section shown, the distance of the plastic neutral axis from the bottom is * 8 in 2 in…

A: Given data in question Dimensions of unsymetrical I sections To find out Depth of plastic neutral…

Q: How many forces are acting in X Direction? Hint: Draw FBD and break forces into Components B 30% FAE…

Q: 10 mm 50 mm 10 mm 80 mm 10 mm

Q: In the figure shown, compute the following : 75 mm 75 mm - 75 mm-

Q: The composite beam shown in the Figure 1 is constructed from wood and reinforced with a steel strap…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. If 1 grid…

A: Given I grid square = 7MPa

Q: The shown circular bar is fixed to the left wall. It has a diameter of 0.5 in and length of 60 in at…

A: for having stress free of right wall, bar should be elongated maximum equal to the gap.

Q: A steel bar showed a percentage reduction in cross-sectional area of 19.5%. The final diameter of…

A: Given data,FINDTo calculate the initial diameter of the bar(D1)

Q: 4 in 3 in

Q: Locate the centroid of the plate area shown below: (All units are in mm). R10 O. 115 X R30 | 30

Q: Determine the Plastic Section Modulus (Zx) and Elastic Section Modulus ($x). Express your answer in…

Q: m 1 Replace the loading system by an equivalent resultant Force and couple moment acting at point A.…

A: Given F1=130lb F2=60lb F3=180lb

Q: A piece of Titanium originally at 300 mm long is pulled in tension with a stress load of 40,000…

A: Given data - Length of titanium piece = 300 mm Stress = 40000 psi Find out - What is the elongation…

Q: A block of wood 0.25 m thick is floating in sea water. The Specific Gravity (SGw) of Wood is 0.35…

Q: ons. or metal). Draw a picture of your object an

A: In order to take an accurate measurement reading between two graduation markings on a linear scale…

Q: A block of wood 0.10m thick is floating in sea water. The Specific Gravity (SGw) of Wood is 0.85…

Q: A spherical ball of copper having the original Surface area of 20. O0mm² and deformed until the…

A: Let us analyse the question in step 2.

Q: explanation and formula , Please do not copy paste the

Q: ● simple shapes 1,2, and 3) shown in figure 1. Determine the distance and y to the centroid of the…

Q: A thin sheet of rubber in the form of a square is uniformly deformed into the parallelogram shape as…

A: Given the figure of deformation of a thin sheet of rubber as, The average normal strain along…

Q: Before taking measurements, someone usually calibrates the measuring instrument. Describe your…

A: Calibration is the comparison of measurement results provided by a system under test with a…

Q: 28.30mm 28.20mm чомра 6-A 20mm by 20mm square is etched onto a metal bar prior to loading. Upon…

A: To find Poisson ratio and Young's modulus

Q: PROBLEM 1 For the area shown, do the following: a. Determine the centroid with respect to the…

A: Note: As per bartleby guidelines, only 1st 3 subparts need to be solved. For rest of the parts…

Q: Reading sequence 1 2 3 4 5 6 7 8 9 10 11 12 13 Reading the ruler 1.35 1.72 1.98 2.05 2.17 2.76 2.98…

Q: 50 mm A 50 mm 50 mm D, 50 mm 50 mm B

Q: Where does the value for yc in step two come from?

A: Since the unit weight of the concrete for the beam is not given in the problem. Usually the unit…

Q: 2. Find the volume of a regular octahedron if one edge is measured as 9 cm.

A: Given:- The measurement of the one edge of the regular octahedron = 9 cm To determine:- The volume…

Q: 6. What does 'a' in psia mean? a) Pressure is measured below absolute pressure b) Pressure is…

Concept explainers

Temperature related material properties

Temperature-related properties of materials are the properties that change or show any variation with temperature variations. Various properties of materials include physical properties, mechanical properties, chemical properties, electrical properties, magnetic properties, etc. The chemical, electrical, and magnetic properties of materials are important, but the physical and mechanical properties are more important. Based on their composition and chemical bonding, materials are classified as metals, ceramics, polymers, and composites.

Question

Answer the problem with complete solution and box the final answer with 4 significant figure and unit.

Write on a clean paper clearly. And take a picture, scan it then submit here.

Using Nominal Mix Design, calculate the individual quantity of cement, sand, gravel, and water
for the following structural elements of a given project:
1. Column Footings
2. Footing Tie Beams (FTB)
3. Columns
BIG
4. Roof Beams
Given:
FS = 1.54
Pement = 1440 kg/m
Paand- 1600 kg/m
Pgrasel = 1560 kg/m³
Water to Cement ratio = 0.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Differentiate between Force (Flexibility) & Displacement ( stiffness)methods of analysis.
PROBLEM SOLVING. Provide complete solution (formulas and substitution step) for every given problem. Solve continuously (round off on the final answer only). Box final answers, include correct units, and round off to the indicated number of decimal places. Do not express answers in scientific notation.
It is the same as my question before. Please see the image attached. Please also check my previous questions.Thank you and God bless
Write a conclusion about the image
For the given figure below, determine the force that would cause the bar to deform by 1.8x10^-2 inches. Other properties: X-sectional area: 0.25 in^2. E-steel 29x10^6 Ibs/in^2 E-alum= 10x10^6 lbs/in^2. P- Steel Steel Aluminan C 2440 Ibs 04550 Ibs 03520 Ibs 4450 Ibs
A square block, a rectangular block, a triangular block, and a quarter circle block are arranged as shown below. A smaller square chunk was cut from the square block, leaving a hole in the figure. Find the center of mass of the composite figure. Use the axes provided as reference for the origin (0, 0). Square: L units x L units, mass = m Rectangle: (L/2) units x 2L units, mass = 3.5 m Quarter circle: radius = (L/2) units, mass = 5 m Triangle: height = L units, base = (L/2) units, mass = 0.75 m Square hole: L/2 units x L/2 units %3D
pls answer the table also
Please answer the following questions as a reply on this Discussion Provide a Stress-Strain Diagram showing the relationship of shear strain to shear stress. Specify the proportional limit, modulus of rigidity, elastic limit, yield point, ultimate strength and nominal rupture strength. Hint: you can use excel to assign random values of shear stress and strain, and to graph them easily.
Determine the plastic section modulus Zx and elastic section modulus Sx
A block of wood 0.25 m thick is floating in sea water. The Specific Gravity (SGw) of Wood is 0.35 while that of sea water (SGs) is 1.02. Summarize your answer like the format below and Find the minimum AREA of a block that will support a man weighing 80 kg. (Clue: - m^2) 大, Wman = 80 kg Wwooo BF Weight of the man Unit weight of the wood N m Unit weight of sea water Equation of Volume of Wood Block N m Area of the block m? zlzzE