Answer the following: Part A: Reaming is used for which of the following functions (three correct answers): (a) accurately locate a hole position (b) enlarge a drilled hole (c) improve surface finish on a hole (d) provide an internal thread (e) improve tolerance on hole diameter (f) all the above Part B: Which of the following statements is applicable to superheating (a) Increased superheating improves surface finish (b) Increased superheating helps to promote mold filling (c) Increased amount of superheating increases total cost (d) Represents the extra heat above the liquidus temperature in the melt (e) All of the above (f) None of the above

Answer the following: Part A: Reaming is used for which of the following functions (three correct answers): (a) accurately locate a hole position (b) enlarge a drilled hole (c) improve surface finish on a hole (d) provide an internal thread (e) improve tolerance on hole diameter (f) all the above Part B: Which of the following statements is applicable to superheating (a) Increased superheating improves surface finish (b) Increased superheating helps to promote mold filling (c) Increased amount of superheating increases total cost (d) Represents the extra heat above the liquidus temperature in the melt (e) All of the above (f) None of the above

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The strength in the weld zone of an age-hardening aluminium alloy is often higher than in the heat affect zone (HAZ). Which of the following is NOT a reason for this? O The maximum temperature is higher in the weld pushing more of the hardening phase into solution. O Particles that don't dissolve might transform into equilibrium phases instead. This is more likely in the HAZ. O The greater dissolution of particles in the weld leads to greater solid solution strengthening. O The increase in solute in the matrix allows more subsequent natural aging to occur in the weld zone. O Particles in the HAZ tend to dissolve, while those in the weld coarsen. The increase in particle size and spacing reduces the strength of HAZ.
I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following:What is the Bolt size (don't worry about the tolerances)?Dim's C=.75, B=2.50, apply a +/-.01 tol to all affected dim's except the .50+/-.03 dim, how far does EDGE D stick out above EDGE E (figure it off the centerline, don't worry abou the clearance between the bolt and the holes)?Min = ? Max= ?
1) What does the specification "8.8" in the standard designation of a bolt mean? Specify values including units. 2) Name two groups of standards in addition to national, industry-wide standards and where they are valid. 3) Which three options exist for defining dimensional tolerances in a technical drawing?
Angle of bite in radian ?
18. Compressive stress can be defined or described as an internal force ina material resisting a 16. The feed rate unit on lathe machine is Millimeter per second b. Millimeter per stroke Millimeter per revolution d. a. C. Millimeter 17. Which part of the marking gauge is used to mark lines on Wood? a. To measure the ductility of weld metal b. To test the skill of a welder To perform a non-destructive test d. To approve welds to certain standards C. a. pulling load. b. shearing load.. pulling and shearing load. d. pushing.load. С. r further smnothing a planed surface?
Note: Please do not handwritten.
what are some of the ways by which the blades of windmill be improved?
500 mm 130 mm 200 mm 1) The oblique pipe in the figure is desired to be compressed. Force F is applied perpendicularly to the pipe wrench. Calculate the difference that will occur if the same key and the same force are applied between AB?
What does the headgear of a mine do?
Need questions 13, 14, 15 explained and answered please.
Question 12 Based on the diagram below, calculate the stress at each hole, assuming that the holes are sufficiently far apart that their effects do not interact. Thickness 0.50 in 1.40 in .0.72-in L0.40-in 0.50-in dia. 6200 lb dia. dia. Axial tensile force
Quèstion 25 Which of the following describes the effect of shot peening on fatigue life? O A. It has no effect on fatigue life O B. It decreases fatigue life because of increased surface hardness O C. It increases fatigue life because of induced compressive stresses D. It decreases fatigue life because of excessive surface deformation A Moving to another question will save this response. 34°C äolo claw ENG 4)