the partsAnswer the followingelating to the drawing in figure (3a):1- What is the name of the component?2- What size is the oil hole? How far is the oil hole from the edge of thecylinder?3- How many holes have to be drilled $12?4- What is the overall height of the finished item?5- What welding is specified by the symbol marked A?6- How many pieces are used to make this item?7- What sizes of welds are used? How thick is item 2?8- What are the general tolerances? How many surfaces are machine finished?63 all hole -4 holes 012BO3²844.005 ROUND BARMINOR WEDSSection A-A6PARTS LIST425x6MS70xBx56MS3 ROUND BARBEOXDOMS2 MAIN WEB200xBx35 MS1 BASE PLATE200x400x120 MSITEMDESCRIPTIONSIZEMATLAND ENGINEERINGDRAMAFRACEDCHECKEDTAFE:K BERYCES CONSORTIATITLESHAFT SUPPORT BEARINGSCALE1202-MF 1- MY 98FTYP140200←All welde et unicee indicated otherwiseFirstCHANGEAMENDMENTSNOTE:70/98ISSUE DATE-ALZ DOECH BY CKD825UN ES NOTED OTHERANSETOLERANCES ARE:UNEAR &0.5ANGULAR &0° -30DRAMING PRACTICEAS TOOFigure (3a)0-17MATREALUNOHG125/4SIZE DRG NA35SHT10F1

A rotational or sliding motion for two parts or maybe more or support an applied load is a shaft…

Answer the following elating to the drawing in figure (38): 1- What is the name of the component? 2- What size is the oil hole? How far is the oil hole from the edge of the cylinder? 3- How many holes have to be drilled $12? 4- What is the overall height of the finished itam?

Answer the following elating to the drawing in figure (38): 1- What is the name of the component? 2- What size is the oil hole? How far is the oil hole from the edge of the cylinder? 3- How many holes have to be drilled $12? 4- What is the overall height of the finished itam?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

help! please write the correct answer. no long explanation needed! upvote will be given! Mechanics of Deformable Bodies A closed cylindrical vessel contains a fluid pressure of P (Mpa). The cylinder has an inside diameter, d (m) and a wall thickness, t (mm) made of steel alloy with yield strength of 340 Mpa. What is the maximum allowable pressure (MPa) if d = 2.50 m and t = 31.8 mm using a factor of safety of 2.5? (2 decimal places)
How many balls of 50 mm diameter fit in a volume of 1910 L
Please answer all becuase they are all connected! UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic material having a tensile and compressive yield stress of o,, determine the following: Given: Allowable Stress = 300 MPa a = 20 mm b = 250 mm c = 250 mm This is already answered in bartleby but please recheck. Thanks a. Calculate the moment of inertia I, in x10 mm4 (If your answer is 667,335 x10 mm, then type 667.335) b. Calculate the yield moment of the section in kN.m. c. Calculate the plastic moment of the section in kN.m d.Calculate the shape factor of the section.
Question 3) On the plate in the figure, the length L is given as L=72 m . According to this; Question 3-A) Find the X coordinate of the geometric center of the plate . ( Enter your result without writing m units. Write at least three digits after the comma.) Question 3-B) Find the Y coordinate of the geometric center of the plate . (Your result m in size Enter the writing unit. Enter the form of at least three digits after comma.)
I need parts 3 and 4 answered pertaining to the print provided. I asked this question previously on here and I received the wrong answers to the 2 parts Im asking about, so I am reposting the question again to have another tutor answer it. Part 3: I need to tell what was ommited. Part 4: I need to tell what the triangle equals? Lower right or J1 zone has the answer.
Select the correct statement about the notation circled in green and marked as letter F. Assume all dimensions are in mm. T 50 1 DRILL 17/64 2 HOLES R.75 00.63 THRU 1.00 2.00 100 50 1.38 3.38 38 SCALE 2.000 2.00 A
Oo.33. Subject:- Mechanical engineering
I need problems 7, 8, and 9 answered pertaining to the print attached below.
I need help answering this Review Activity
Please answer the given question and show the solution. Thank you very much! Note: Please include the units in the solution and use 4 decimals point in Final Answer.
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
QUESTION 4 needs to be answered,