ANS.A cylindrical tank having diameter d = 2.5 in. is subjected to an internal gaspressure p = 600 psi and an external tensile load T = 1000 lb (see figure). Determine theminimum thickness of the wall of the tank based upon an allowable shear stress of3000 psi.0.125 inchesTT

Step 1: (1). Determine the Hoop Stress (σh) due to Internal Pressure: The hoop stress…

Answered: ANS. A cylindrical tank having diameter…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A prismatic bar is subjected to an axial forcethat produces a tensile stress σθ = 65 u MPa and ashear stress τθ = 23 u MPa on a certain inclined plane(see figure). Determine the stresses acting on all facesof a stress element oriented at θ = 30°, and show thestresses on a sketch of the element.
A 30 mm square is drawn on the rim of a large steel pressure vessel. The biaxial stress situation in the square after the pressure is applied is as shown in the figure. Determine the change in length of the BC edge in (mm).
The simply supported beam shown supports a uniformly distributed load of w = 50 kN/m. Assume x = 1.6 m, a = 3.5 m, b = 6.0 m, xk = 2.5 m. The cross-sectional dimensions of the beam are b₁ = 305 mm, t₁ = 23 mm, d = 480 mm, tw = 14 mm, and y = 85 mm. Determine the principal stresses and the maximum shear stress acting at point H. On a piece of paper, show these stresses on an appropriate sketch. ΧΗ พ bf H H B K Ун XK Ук b K a tw d
The tank shown in Figure below is fabricated from t = 1/8 in steel plate. The maximum longitudinal and circumferential stress caused by an internal pressure of 125 psi (Ib/in²). 1. Drive the expressions for longitudinal and tangentional stresses? 2. Calculate the maximum longitudinal and circumferential stress caused by an internal pressure? Fw Fw Fp Fp XLV 1.5 ft |1= 1/8 in Fw Fw Fw Fw 0.75 ft LONGITUDINAL STRESS, ₁ TANGENTIAL STRESS , 2 ft 1.5ft ث إضافة ملف
A simple pin-connected truss is loaded and supported as shown in the figure. All members of the truss are aluminum pipes that have an outside diameter of 3.00 in. and a wall thickness of 0.210 in. Determine the normal stress in truss member BC. Assume P = 4 kips, Q = 2 kips, a = 5 ft, b = 9 ft, and c = 7 ft. The stresses are positive if tensile and negative if compressive. Answer in ksi rounded-off to 2 decimal places. P e (3) B b T Gra a Adc Ref you
A cast iron link has dimension of 40 x 200 x 500 mm as shown in the figure. The compressive load P = 400 kN is applied to the ends of the link along a longitudinal axis that is located 150 mm above the bottom of the link (50 mm above the neutral axis). Determine the normal stress developed at the bottom surface point A. 50 mm NA- 150 mm 200 mm A 500 mm 40 mm
50 N/m. 3. For the beam shown below, let wo = 90 N/m and w = Wo W1 | A -2 m 2 m 3 m 3 m -2 m Figure 2 Loaded Cantilever Beam a. Find the reactions at A. b. Find the loading function q(x) using singularity functions. c. Find the shear and moment functions V(x) and M(x). d. Determine and plot the shear diagram for the given loading conditions. e. Determine and plot the moment diagram.
Problem 3 A large spherical tank (see figure) contains gas at a pressure of 3.5 MPa. The tank is 20 m in diameter and is constructed of high-strength steel having a yield stress in tension of 550 MPa. (a) Determine the required thickness of the wall of the tank if a factor of safety of 3.5 with respect to yielding is required. (b) If the tank wall thickness is 100 mm, what is the maximum permissible internal pressure? (Assume that the given radius or diameter is an inside dimension and that all internal pressures are gage pressures.)
Find the stresses in each direction, also find the change in volume of the block of dimension 120 mm x 60 mm x 43 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 10 kN (tensile), 25 kN (tensile), 13 kN (compressive) respectively, Take E as 180 GPa, Poisson's ratio as 0.3. The stress along length direction (Unit in kN/m2)= _____________ The stress along width direction (Unit in kN/m2)= _____________ The compressive stress along depth direction (Unit in kN/m2)= _____________ The change in volume of the block is (unit in mm3) = ______________
A = Tab Problem 1. An ellipse with semi-major axis a = 150 mm and semi-minor axis b = 100 mm is etched on a brass plate. The plate has dimensions 400 x 400 × 20 mm. Uniformly distributed normal stresses ox = -25 MPa and o, = 50 Mpa are applied to the plate. The Young's modulus E = 100 GPa, and Poisson's ratio v = 0.34. (Note: The ellipse remains an ellipse after stretching, but with different semi-major and semi-minor axes.) Find: a) The change in the area of the ellipse. Oy The in the thickness of the plate. b) c) The change AV in the volume of the plate. Ox a. -b- Ox a d) The strain energy, U, stored in the plate. Ty
PROBLEM 2. The carrier system in the figure consists of the AB rigid beam and two aluminum bars and a steel bar connected to it. After the assembly is created at 20 °C without causing any prestresses, calculate the stresses on the bars if the temperature is increased to 80 C. Steel A-36 A =160 mm? 3,5m 10 kN/m 3 m 3m 2 m 2014-T6 Aluminum A =200 mm E A,
CN=44

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

ANS. A cylindrical tank having diameter d = 2.5 in. is subjected to an internal gas pressure p = 600 psi and an external tensile load T = 1000 lb (see figure). Determine the minimum thickness of the wall of the tank based upon an allowable shear stress of 3000 psi. 0.125 inches T T