and The base Current is C4 mA) , Then method - If The emitter Current is (44 mA) Y Connecting atransistor by the common bale method. If The emitter current is (44 mA) and The base Current is (4 mA), Then RR = l00 2 Rc 5 000 s2 %3D calculate: D Zoom factor ( B) 2 Potential difference amplification ratio

and The base Current is C4 mA) , Then method - If The emitter Current is (44 mA) Y Connecting atransistor by the common bale method. If The emitter current is (44 mA) and The base Current is (4 mA), Then RR = l00 2 Rc 5 000 s2 %3D calculate: D Zoom factor ( B) 2 Potential difference amplification ratio

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
Using a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 60hz, a value of 100u for the Capacitor, a silicon diode and a resistor with the value of 1000 ohms. Find the voltage value on the resistor at a simulation of 20ms. 2Vm Vm Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
A clamper circuit has 20 Vp-p. 100Hz square wave input voltage. The circuit consists of silicon diode IN4001 and 3V battery as shown in Figure 1 C. 0.1 µF D R Vi(t) 50 k2 Vo(t) 3 V Figure 1 a) Find the output voltage for all input voltages values. b) Sketch the output waveform, Vo(t).
What is the value of Rmin for the Zener voltage regulator circuit shown in 3.39 and 3.40? What is the output voltage for RL =1kΩ? For RL =2kΩ?
After replacing R5 with diode IN4007 (switch K3 to diode side) .What conclusion can you draw from analysis of this step ?
Draw a circuit with silicon diodes that has the transfer characteristic shown in figure (3). AVo 4.5 -2.8 -15 4.5 15 -2.8 Figure (3)
Show the output voltage for the Vi input voltage in the figure by drawing it along a period (Note: the diode used is a silicon diode, and it won't be considered an ideal diode)
Using an ideal diode, design a clamper circuit that result in the desired output waveform as shown in Figure Q7. Show overall analysis to justify the proposed design. 7. Vo Vi Designed Clamper Circuit - 3 V -20 - 43 V - Fiqure Q7 20
5. A JFET has a specified pinch-off voltage of 5 V. When VGs = 0, what is Vps at the point where the drain current becomes constant?
The Pinch off voltage for N-Channel JFET is -3V, maximum saturated drain current 8mA and the value of VGS is -1.5 V. Calculate drain current, a. 4 mA b. 2.5 mA c. 2 mA d. 18 mA
4. An RC filter stage (R = 33 , C = 120 µF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
If the load resistance value Rl is 2 kohm in this circuit and the DC component of the output signal is 5V, calculate the AC output power of this circuit. The diodes used are silicon diodes, their operating voltage is 0.7 Volt and their resistance can be neglected since they are very small.