An RCC beam having 200 mm wide and 400 mm effective depth is reinforced with Fe415 grade steel of area 1000 mm² in tension. Assume M20 grade concrete, what is approximate value of the depth of neutral axis for the equilibrium of forces at the limit state of collapse? (a) 200 mm (b) 250 mm (d) 350 mm (c) 300 mm

An RCC beam having 200 mm wide and 400 mm effective depth is reinforced with Fe415 grade steel of area 1000 mm² in tension. Assume M20 grade concrete, what is approximate value of the depth of neutral axis for the equilibrium of forces at the limit state of collapse? (a) 200 mm (b) 250 mm (d) 350 mm (c) 300 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6. Which of the following is the compressive strength of concrete if β1=0.85. a. 21 MPa b. 33 MPa c. 35 MPa d. 56 MPa 7. Which of the following is the compressive strength of concrete if β1=0.65. a. 35 MPa b. 21 MPa c. 60 MPa d. 42 MPa 8. Which of the following is the compressive strength of concrete if β1=0.80. a. 60 MPa b. 21 MPa c. 35 MPa d. 42 MPa 9. For parallel non-prestressed reinforcement in a horizontal layer, clear spacing shall be at least the greatest of the following except a. 25 mm b. 30 mm c. diameter of the steel bar d. 4/3 of the aggregates nominal size 10. For parallel non-prestressed reinforcement placed in two or more horizontal layer, reinforcement in the upper layers shall be placed directly above reinforcement in the bottom layer with the clear spacing between layers of at least a. 30 mm b. diameter of steel bar c. 25 mm d. 4/3 of the aggregates nominal size 11. Adding bars will impart significant increase in the moment strength of flexural members…
Strength of Materials Answer should be 0.378 x 10-3 m2 ; 13.02 kN/m :) A concrete beam of rectangular section is 10 cm wide and is reinforced with steel bars whose axes are 30 cm below the top of the beam. Estimate the required total area of the cross-section of the steel if the maximum compressive stress in the concrete is to be 7.5 MN/m2 and the tensile stress in the steel is 135 MN/m2 beam is subjected to pure bending. What bending moment would the beam withstand when in this condition? Assume that Young's modulus for steel is 15 times that for concrete and that concrete can sustain no tensile stresses.
A flexure strength tests were performed on a concrete beam having a cross section of 0.15x0.15m and a span of 0.45m. If the total load at failure was 37.5kN, calculate the ff:a. The flexure strength of the concrete if center-point was applied.b. The flexure strength of the concrete if third-point was applied.c. Which of the two flexural tests is recommended in determining the flexure strength of the concrete and why?
Using the same concrete dimensions as were used for the second solution of Example 3.6 (b = 10 in., d = 17.5 in., and h = 20 in.) and the same material strengths, find the steel area required to resist a moment M, of 1300 in-kips. %3D
A 150mm x 150mm concrete specimen was tested for flexure strength over a span of 600mm. The load at midspan causes a flexure strength of 41.4 MPa. What was the maximum applied load in kN?
Given fc' = 35 MPa, solve for the modulus of elasticity of concrete a. 27,800.00 MPa b. 27,805.57 MPa c. 200,000.00 MPa d. None of the above If fc'= 42 MPa, solve for B. a. 0.65 b. 0.75 C. 0.85
Determine the maximum concrete and steel stresses at the point of maximum positive and negative moments. Reinforced Concrete Design
Rcc
The maximum load of 200 KN was applied on a cylindrical specimen of concrete. Find the split tensile strength in MPa. Take depth as 150 mm and length as 300 mm.
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 400 mm. Concrete strength is f’c = 28 MPa and steel yield strength is fy = 280 MPa. a. What is the distance of the neutral axis from the top of the beam so that the strain in the concrete 0.003 will be attained at the same time with the yield strain of steel? b. What is the total compressive force on concrete? c. What is the balanced steel ratio?
If a concrete column 200 x 200 mm in cross- section is reinforced with four steel bars of 1200 mm² total cross-sectional area. What is the safe load for the column if permissible stress in concrete is 5 N/mm2 and Es =15 Ec?
Reinforced concrete designs (Solution working stresses method)