An open cylindrical vessel 1.2 m in diameter and 2.1 m high is 2/3 full of water. Compute the amount of water that will be spilled out of the vessel if the vessel is rotated about its vertical axis at a constant angular speed of 90 rpm. Select one: O a. 16 liters O b. 13 liters O c. 9.6 liters O d. 10 liters

An open cylindrical vessel 1.2 m in diameter and 2.1 m high is 2/3 full of water. Compute the amount of water that will be spilled out of the vessel if the vessel is rotated about its vertical axis at a constant angular speed of 90 rpm. Select one: O a. 16 liters O b. 13 liters O c. 9.6 liters O d. 10 liters

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

نقطة واحدة * :Q 5 Q: The tank in Figure is closed at top and contains air at pressure PA. Calculate the value of PA of manometer readings shown. Air Open tube Oil(S.G-0.7 150 cm 200 cm Wat 10 cm Mercury
A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the water when a piston applies a pressure of 36 MPa. ! m³
A cylindrical object 82mm diameter, 155mm height and a mass of 611g, is placed in the tank, which contains oil(51mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 943 kg/m3.
A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 260 kPa, determine the gage pressure of the gasoline line. Assume the density of air to be 1.225 kg/m3
ı need solution
A cylindrical object 84mm diameter, 158mm height and a mass of 593g, is placed in the tank, which contains oil(51mm thick) and water. Calculate the height(in mm) above the surface of the oil at which it will float if maintained in the vertical position. Take density of oil equals 973 kg/m3. Answer in two decimal places.
V=38 h1=96 h2=12 D1=6 D2=3 angle = 20 degree
A pressurized tank contains water with some air above it. As shown on figure below. Multi-fluid manometer is used to determine the pressure at the air-water interface ( If hi= 0.7 m, hz=0.4 m, h3=D0.55 m and ha = 0.85 m. Also, specific gravity of water = 1 and specific gravity of crude oil = 1.8 and specific gravity of mercury 12.5 and specific gravity of shale oil = 2.5 Determine the absolute pressure at point 5 in Pascal unit. [Given: g =9.81 m/s2 and atmospheric pressure 101300 Pa] Mercury S.G. 125 Water S.G. -1 he Crude oil S.G. 18 Shale oil S.G. 25
The Venturi meter shown in the sketch below, contracts the flow down to one quarter of its original area. Cold air at 0 deg C flows in the pipe through the Venturi meter. The velocity of the air upstream of the Venturi meter is equal to 40 ft/s and the pressure at the same point is equal to 30 psia. What is the manometer reading if the fluid of the manometer is water with density 1000 kg/m3 . Assume that the air behaves as an ideal gas with molecular weight equal to Mw=29 kg/kmol and constant density evaluated at upstream conditions. Use Bernoulli's equation for your calculations. please respond asap!
A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.83 mm. The nozzle shoots out water moving at 25.0 m/s. 1. Required information At what speed is the water in the hose moving? cm/s Required information What is the mass flow rate? g/s 2.
Find the volumetric flow rate of the oil in m3/s thank you!!