An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)

An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.113P: Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels...

See similar textbooks

Similar questions

In the given question/s find the fluid force on the vertical side of the tank, where the dimensions are given in feet.Assume that the tank is full of water:- (See the figure as attached here).
Q3) Compute the horizontal and vertical components of the water pressure acting on the face of tainter gate AB of 72° sector of radius 25 ft as shown in Fig.2.Take the width of the gate as unity. The specific weight of water = 62.4 Ib/ft³. 25ft Water C 25-ft radius 36° + 36⁰
Q4: A tank 25 ft deep and 8 ft wide is layered with 8 ft of oil, 6 ft of water, and 4 ft of mercury. Compute(a) the total hydrostatic force and (b) the resultant center of pressure of the fluid on the right- hand side of the tank.
A vessel is filled with oil (ρoil = 900 kg/m3) up to 1 m of its height. It is 3m wide, 2m high and 10 m long.Find the following :A. The maximum horizontal acceleration that can be charged to the vessel without spilling anyoil.B. If this vessel is closed and is completely filled with oil and accelerated horizontally at a rate of 3 m /s2 .B.1. The total force acting at the rear wall and at the front wall of the vessel.B.2. The accelerating force on the fluid mass.
May The tank in Fig. 2 is 3 m wide into the paper. Compute the hydrostatic (a) horizontal force component (b) vertical force component and (c) resultant force and its angle on the quarter-circle panel BC. Water 4 m C 4 m. B 6m
1. Hydrostatic Force on Plane Surface. An open rectangular tank is 7 m high and has a square base 5 m on a side. If the tank is half-filled with fresh water (density is 1000 kg/m'), determine (a) the total hydrostatic force on a vertical side, in kN and (b) the location of the center of pressure as measured from the liquid surface, in cm. Draw the side view of tank showing the hydrostatic force F and the distance, yp. Is I + Ad a. Magnitude: F = yh,A b.Direction: Perpendicular to the Area c. Location: y, === S.
Q3) Find the horizantal and vertical pressure force exerted on the gate (AB) of the tank. I [Tank length = 3.5 m). P=15kq Water r=2m
B3. A rectangular plate of width 35 mm, depth =85 mm is vertically placed in water in such a way that the centre of the plate is 3.25 m below the free surface of water. Draw the diagram neatly. Find the total pressure & center pressure on the plate. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Total Pressure on the circular plate (in N) Centre of Pressure on the circular plate (in m)
A tanker contained with water is pushed horizontally at constant acceleration of 5.0 m/s?. If the tank is 10 m long and the depth of the water is 3 m when at rest, Calculate; a) The angle of water surface to the horizontal. b) The maximum pressure intensity on the bottom
A vertical plate is submerged in water and has the shape as seen in the picture. Using the facts that the density of water is 1000 kg/m³ and acceleration due to gravity is 9.8 m/s², calculate the hydrostatic force (in N) against the end of the tank. Make sure your answer is correct to the nearest thousand. (Hint: First set up a Riemann sum that approximates the hydrostatic force, which can then be used to obtain an integral that represents the force.) 20 m Hydrostatic force =
A gate rotates at point A and releases water when the water's depth, d, exceeds a certain value. The gate's width (perpendicular to the image) is b = 2.95 ft, the water's depth is d = 4.82 ft, and point A is located at h = 2.41 ft. a) What is F, the magnitude of the horizontal force exerted on the gate by the water? The water's specific weight is γw=62.4lb/ft3. b) What are Ax and Bx, the horizontal reaction forces at points A and B that act on the gate from Part A. c) What is dmax, the water's maximum depth before the pressure causes the gate from part A to open?
One side dimension of a rectangular tank is 1.5 m and 2 m deep. The tank filled with oil of mass density of 920 kg / (m ^ 3). Calculate the resultant force on this vertical end and the depth of the centre of pressure from the top.