An oil refinery uses a Venturi tube to measure the flow rate of gasoline. The density of the gasoline isp = 7.10 x 102 kg/m³, the inlet and outlet tubes, respectively, have a radius of2.36 cm and 1.18 cm, and the difference in input and output pressure is P, - P, = 1.20 kPa.P1P2(a) Find the speed (in m/s) of the gasoline as it leaves the hose.m/s(b) Find the fluid flow rate in cubic meters per second.m/s

Given data Density of gasoline = 710 kg/m3Radius at point 1 = 2.36 cm = 2.36 x 10-2 mRadius at point…

An oil refinery uses a Venturi tube to measure the flow rate of gasoline. The density of the gasoline is p = 7.10 x 10 kg/m, the inlet and outlet tubes, respectively, have a radius 2.36 cm and 1.18 cm, and the difference in input and output pressure is P, - P, = 1.20 kPa. P (a) Find the speed (in m/s) of the gasoline as it leaves the hose. m/s (b) Find the fluid flow rate in cubic meters per second. m2/s

An oil refinery uses a Venturi tube to measure the flow rate of gasoline. The density of the gasoline is p = 7.10 x 10 kg/m, the inlet and outlet tubes, respectively, have a radius 2.36 cm and 1.18 cm, and the difference in input and output pressure is P, - P, = 1.20 kPa. P (a) Find the speed (in m/s) of the gasoline as it leaves the hose. m/s (b) Find the fluid flow rate in cubic meters per second. m2/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q- fluids, The Coefficient of discharge of a orifice meter is 0.97. The time taken by fluid to cover…

Q: A package shown in Figure 2 is dropped from the plane which is flying with a constant horizontal…

Q: Q2: Find the piezometric head at tank (C), if the discharge in pipe (1) = (65 L/sec). Use (-0.025)…

A: 2) Given: find the piezometric head at tank c Q1= Discahrge in pipe 1=65…

Q: If the pump efficiency is 75 percent, the power motor required to drive it is:

Q: Two chambers, Chamber 1 and Chamber 2 where pressure at chamber 1 p1=70 kPa, at chamber 2 the…

A: To determine the actual flow rate through the orifice

Q: Pumps and fluids transport system. Definition and three (3) examples of the following: 1. Pumps and…

A: Given Pipe and its types Pipelines Tank To find Definition and Example

Q: This is unit analysis. Explain and Plot the whole process why the head(h) arrive in meter(m) unit…

Q: Consider the two flows below involving a pipe and nozzle where the inlet area is greater than the…

Q: The volume of air delivered by fan is 14 m^3/sec and 69 mm water gage. The density of air is 1.27…

Q: the gauge pressure at point B. Two reservoirs are connected by a pipe 40 cm diameter and 2000 m…

A: Upon the neglecting the minor losses we know that pa=pc=0vA=VC=0 Applying the Bernoulli equation…

Q: Q1/ For fig shown if water flow rate is 60 lit/s , Find (h) Note that Density: Pwater = 1 kg/m Pair…

Q: In an aorta aneurysm, a bulge forms where the walls of the aorta are weakened. If the blood flowing…

Q: certain liquid (SG = 13) flows through a 483-cm diameter pipe at a velocity of 7.5 m/s. Find the…

A: Given:SG=13d=483 cmv=7.5 m/s

Q: A certain SSSF control volume with a single inflow and outflow and has an inflow speed V₁ = 200…

Q: ; An air tank has a volume of 2 m³. In the beginning the air pressure in the tank is 150 kPa. Then…

A: The volume of the tank, V = 2 m3 Initial pressure, P1 = 150 kPa Gas constant, R = 287 Jkg-K Initial…

Q: In the figure shown below the water comes out of a tank and runs through pipe 1 (D1=10cm) that…

A: The flow velocity in pipe 1 is 7.5 m/s.

Q: 3. In the figure, ideal fluid (water) flow from the infinity large basin through the atmosphere.…

Q: A certain liquid (SG = 12) flows through a 401-mm diameter pipe at a velocity of 6.5 m/s. Find the…

Q: A 30 cm pipe carrying water, branches into two pipes of 20 cm and 15 cm diameter. If mean velocity…

Q: A horizontal pipe of diameter 550 mm is suddenly contracted to a diameter of 300 mm. The pressure…

Q: Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW…

A: Given Volume, V= 1.78 L = 0.00178 m3 Brake power, BP = 28 kW Speed, N = 2500 rpm…

Q: An orificemeter with ortfice diameter 12 cm is inserted in a pipe of 20 cm diameter. The pressure…

A: Given Data, d0=12 cm=0.12 m (orifice)d1=20 cm=0.2 m (pipe)p1-p0=9.81 N/cm2Cd=0.6

Q: A circular pipe CD carries 1/3rd of flow in AB. Find volume rate of flow in AB, diameter of BC,…

Q: Q4: Three pipes (A, B and C), if diameter of A equal to B, diameter of A less than C by 25%,…

Q: A circular pipe CD carries 1/3rd of flow in AB. Find volume rate of flow in AB, diameter of BC…

Q: 2. A pump 260mm suction pipe and a 150mm discharge pipe is used to deliver 58L/s of water. The…

A: Suction pipe diameter, d1=260 mm=0.26 mDischarge pipe diameter, d2=150 mm=0.15 mWater flow rate,…

Q: In the Impact of a Jet experiment, Mass=36g, water volume collected=5.0 Liter, time=30 seconds,…

Q: Please try to answer in text Water flows through 100 mm diameter pipe from A to B. The velocity is…

A: Hydraulic grade line is defined as piezometer head.

Q: A pump 254 mm suction pipe and a 127 mm discharge pipe is used to deliver 52 L/s of water. The…

A: Given: The length of suction pipe, Ls = 254 mm The length of discharge pipe, Ld = 127 mm The flow…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

An oil refinery uses a Venturi tube to measure the flow rate of gasoline. The density of the gasoline isp = 7.10 x 102 kg/m³, the inlet and outlet tubes, respectively, have a radius of
2.36 cm and 1.18 cm, and the difference in input and output pressure is P, - P, = 1.20 kPa.
P1
P2
(a) Find the speed (in m/s) of the gasoline as it leaves the hose.
m/s
(b) Find the fluid flow rate in cubic meters per second.
m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water is pumped into a fire hose through a 6 cm diameter pipe with speed 1m/s. The water in the fire hose flows with a pressure of 200000 Pa. At the end of the fire hose is a nozzle (small hole). The pressure decreases to atmospheric pressure (101300 Pa) when the water leaves the nozzle from the hose. There is no change in height moving from the hose to the nozzle. 1. What is the water speed in a 4 cm diameter fire hose? 2. What is the velocity of the water exiting the nozzle (p=1000kg/m³)? 4. What is the diameter of the nozzle? 3. A Fireworker now connects an additional flexible tube to the nozzle (tube and nozzle has same diameter). He lifts the tube to a height of 1 meter above the ground. At what speed does the water come out of the tube? (hint - the pressure at the exit is still atmospheric)
please answer asap
.A hydraulic pump delivers 13.5 litres per minute towards pressure of 310 bar.Find the following (a) Calculate the hydraulic power in kW (b) If the overall efficiency of the pump is given as 63% .Find the input of electric power needed to drive the pump in watts (a) The hydraulic power (in kW) = (b) The power of electric motor needed to drive the pump (in W) =
The length of a tube carrying fluid is increased by 1.75 times its original value. All other parameters remain unchanged. What is the new flow rate through the tube if the original flow rate before the increase in length was 4.50. L/min? (Usc Poiseuille's Law), : 2P 87) L
Find the air horsepower of an industrial fan that delivers 55 000 cubic feet of air per minute (25.977 055 m3/s) through a 3 ft. (0.914 634 meter) by 4 ft. (1.219 512 meters); pressure is 5 in. (127 mm) of water; air temperature is 700 F (21.1110C) and barometric pressure is 29.92 in. (760 mm) of mercury. Note: Quantities in parentheses are by the author.
The volume of air delivered by fan is 12 m^3/sec and 59 mm water gage. The density of air is 1.9 kg/m^3 and the motor power needed to drive the fan is 50 kW. Determine the fan efficiency in % Answer in whole number
I need a simple step by step answer please :)
Only handwritten no Chatgpt.
i need the answer quickly