Answered: An oil of sp. gr. 0.9 is contained in a…

An oil of sp. gr. 0.9 is contained in a vessel. At a point the height of oil is 40 m. Find the corresponding height of water at the point.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A piston is used to support a load of 90 kN. The hydraulic oil used has a specific gravity of 0.81.…

Q: 52. If the unsupported length of a stanchion is 4 meters and least radius of gyration of its cross-…

A: given- unsupported length Leff=4 m= 400 cmrmin=5 cm

Q: A Y-shaped tube is inserted upside down so that the left foot and right foot are immersed in two…

A: Given- density of first liquid ρ1=0.80 g/cm3density of second liquid ρ2=0.75 g/cm3height of the…

Q: The pressure exerted on a liquid increases from o kpa. The volume decreases by 1%. Determine the…

A: The bulk modulus is a measure of the ability of a substance to withstand changes in volume under…

Q: Problem 4 A mound of blue powder dye is placed on a flat surface in the x-y-plane as shown. The flat…

A: We have to determine the value of volume of dye in the mound and location of the centre of gravity…

Q: 21. The dynamic viscosity of a water in the SI is in "Pascal second". It is equivalent to * 0.10…

Q: A solid cone of radius ro and vertex angle 20 is to rotate at an angular velocity w. The cone is…

Q: An oil film of 1-mm thickness is between a 1-meter x 1-meter square plate weighing 350-N sliding…

Q: A cube of material is 4 in. on a side and floats at the interface between kerosene (SG=0.82) and…

Q: 1. A water sample is known to contain 300 g/m3 of casein (C8H12O3N2). Estimate the COD, BODu, and…

A: Given data: Mass of sample of casein m=300 gm/m3 Deoxygenating Constant at temperature 20°C=…

Q: A sphere 1m in diameter floats half submerged in tank of oil (SG=0.80). What should be the weight of…

A: Buoyancy force isFB=1243π0.53 γoilWeight of sphere isWS= 43π0.53 γSUsing equilibrium :∑…

Q: *A 40-lb, 0.8-ft-diameter, 1-ft-tall cylindrical tank slides slowly down a ramp with a constant…

Q: Determine the mass density, specific weight, and specific volume of the oil acting on a plate.

Q: Moving Plate, F, V The gap between the two parallel plates contains two different fluids of…

A: from fluid fluid interface condition τ1=τ2μ1dudy=μ2dudy0.1V1-00.5*10-3=0.151-V10.3*10-3V1=0.71428…

Q: An aluminum block (SG=2.5) has a dimension of 0.24 m x 0.24 m xh meters. It is floating in mercury…

Q: The bulk modulus of water is 2.0 x 10° N/m². The pressure required to increase the density of water…

A: Bulk Modulus of water =2×109 N/m2

Q: After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of…

A: Depth upto which SAE oil is filled in a glass to make it float on water = d , Specific Gravity og…

Q: DETERMINE THE VALUE OF MP.

A: ##Calculation plastic moment Mp of beam

Q: A solid cone of radius r and vertex angle 20 is to rotate at an angular velocity w. The cone is…

A: Object: Solid coneDimensions: Radius: Vertex angle: 2θHousing: Present, with a gap between the…

Q: A conical vessel has a height of 24 cm. and a base diameter of 12 cm. It holds water to a depth of…

Q: A rectangular block of wood, floats with one face horizontal in a fluid (RD = 0.9). The wood's…

A: Given : RD = 0.9 Wood density = 750 kg/m3 To Find : Determine the percentage of the wood which is…

Q: When a pressure of 2x10 kN/m2 is applied 50 litres of a liquid, its volume is decreased by to 0.5…

A: Pressure = 2 X 10 kN/m2 VOlume = 50 litersDecreased volume = 0.5 litersWe have to determine the bulk…

Q: seed

A: Force due to weight of glassFg=γ2πrth=2.6×9.81×2π×0.052×0.005×0.1Fg=0.00063765π kNForce due to…

Q: ight solid hemispherical blocks each of diameters 4 cm are dropped into a hemispherical vessel…

A: Given data: hemispherical vessel radius: 8 cm solid hemispherical block diameter: 4 cm 8 number of…

Q: An aluminum block (SG=2.5) has a dimension of 0.22 m x 0.22 m xh meters. It is floating in mercury…

Q: Let P and T be the pressure and temperature of the super-heated vapor and Psat be the saturation…

Concept explainers

Thermal Processes

Some of the key areas where thermal processes find their application are:

Question

An oil of sp. gr. 0.9 is contained in a vessel. At a point the height of oil is 40 m. Find the corresponding height of water at the point.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data of a vessel containing oil

VIEW

Step 2: Formula used for calculation

VIEW

Step 3: Calculation of height of water

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(c) Consider the following conditions: Condition 1 Condition 2 A wooden cube of size 2 m and the 20% of the volume of a body is visible relative density of 0.5 floats in the over the free surface of the water. water. Calculate: (i) Volume of the cube submerged in the water, based on Condition 1. (ii) Density of the wooden cube, based on Condition 2.
4
26. An open-top cylindrical tank 1 meter in diameter is 2.80 m tall. The tank floats in water with a draft of 2.30 meters. Unit weight of lead is 110 kN/m^3 a) What is the weight of tank in KiloNewtons? b) How much lead (in KiloNewtons) must be fastened to the outside bottom of the tank in order make it completely submerged in water? c) How much lead (in KiloNewtons) must be placed inside the tank in order make it completely submerged in water? (Ans. 17.72kN; 4.23kN ; 3.85kN)
An aluminum block (SG=2.5) has a dimension of 0.29 m x 0.29 m x h meters. It is floating in mercury (SG=13.6) and the submerged height of the block is 0.85 m. Determine the weight (kN) of the block.
An oil of sp. gr. 0.9 is contained in a vessel. At a point the height of oil is 40 m. Find the corresponding height of water at the point.
Can someone explain where the 32.2 is coming from please
1500 KN 800 mm 70 mm d) Determine the new thickness of the bar in mm e) Determine the percentage change in the total volume of the bar 100 mm 1500 KN
Q2: A drop of liguid foluen is kept al uniform temperkure t 299 K and is suspended in air by a fine wire. The initid radius at r= 2mm. The vapor pressure of foluene 299K is f=384 Kfe and the density of liguid toluene is 366 ky Im 3. Derive equation for the time tp for the drop b evupurete Completely in a large volume of still air Calculate the tine in seconds for Complete evaporahion.
The surface tension of mercury at 60°C is 0.47N/m. What capillary height in mm will occur in this fluid whe in contact with a glass tube of radius 0.3mm? Use 130° for mercury. O 11.5mm fall O 11.5mm rise O 15.1mm fall O 15.1mm rise
Three liquids given the following properties are poured into the cylindrical container with a diameter of 3 meters and a height of 6 meters. First fluid poured: sg = 1.0 , V = 17.6715 m^3 Second fluid poured: sg = 0.81 , V = 10.6029 m^3 Third fluid poured: sg = 2.94 , V = 7.0686 m^3 Assuming that the container is closed after pouring the fluids and the stable state in the container is reached, determine the pressure at the height of 4-m from the bottom of the tank
Problem A gas weighs 16 N/m³ at 25°C and at an absolute pressure of 0.25 N/mm². Deter- mine the gas constant and density of the gas.
Pls show clear and complete solution ty