An object with a mass of 29 g and a volume of 32.0 cm3 is placed in a liquid with a density of 1.25 g/cm3. Find the volume of the part of the object that is NOT submerged in the liquid. Give your answer in cm3 and with 3 significant figures.

A tank with a flat bottom of area A and vertical sides is filled to a depth h with water. The pressure is P0 at the top surface. (a) What is the absolute pressure at the bottom of the tank? (b) Suppose an object of mass M and density less than the density of water is placed into the tank and floats. No water overflows. What is the resulting increase in pressure at the bottom of the tank?

How many cubic meters of helium are required to lift a light balloon with a 400-kg payload to a height of 8 000 m? Take Hc = 0.179 kg/m3. Assume the balloon maintains a constant volume and the density of air decreases with the altitude z according to the expression pair = 0e-z/8 000, where z is in meters and 0 = 1.20 kg/m3 is the density of air at sea level.

Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate the new flow rate for the following changes with all other factors remaining the same as in the original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid with 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube is used with a radius 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half the length, and the pressure difference is increased by a factor of 1.50.

A rectangular block of Styrofoam 25.0 cm in length, 15.0 cm in width, and 12.0 cm in height is placed in a large tub of water. Assume the density of Styrofoam is 3.00 102 kg/m3. a. What volume of the block is submerged? b. A copper block is now placed atop the Styrofoam block so that the top of the Styrofoam block is level with the surface of the water. What is the mass of the copper block?

To allow a car to slow down or stop, hydraulic brakes transmit forces from a master cylinder to the brake pads through a fluid. Imagine this system as a tube filled with an incompressible fluid and a piston on each end. A force of 95.0 N is applied to a piston 2.65 cm in diameter on one end of the tube. a. What is the magnitude of the force that is exerted on the piston 5.15 cm in diameter on the other side? b. If the 2.65-cm piston is displaced by 1.00 cm, by how much is the 5.15-cm piston displaced?

Mercury is poured into a U-tube as shown in Figure P15.17a. The left arm of the tube has cross-sectional area A1 of 10.0 cm2, and the right arm has a cross-sectional area A2 of 5.00 cm2. One hundred grams of water are then poured into the right arm as shown in Figure P15.17b. (a) Determine the length of the water column in the right arm of the U-tube. (b) Given that the density of mercury is 13.6 g/cm3, what distance h does the mercury rise in the left arm?

A spherical weather balloon is filled with hydrogen until its radius is 3.00 m. Its total mass including the instruments it carries is 15.0 kg. (a) Find the buoyant force acting on the balloon, assuming the density of air is 1.29 kg/m3. (b) What is the net force acting on the balloon and its instruments after the balloon is released from the ground? (c) Why does the radius of the balloon tend to increase as it rises to higher altitude?

A small statue is recovered in an archaeological dig. Its weight is measured to be 96 lb, and its volume 0.08 ft3. (a) What is the statue's weight density? (b) What substance is it?

Figure P15.52 shows a Venturi meter, which may be used to measure the speed of a fluid. It consists of a Venturi tube through which the fluid moves and a manometer used to measure the pressure difference between regions 1 and 2. The fluid of density tube moves from left to right in the Venturi tube. Its speed in region 1 is v1, and its speed in region 2 is v2. The necks cross-sectional area is A2, and the cross-sectional area of the rest of the tube is A1. The manometer contains a fluid of density mano. a. Do you expect the fluid to be higher on the left side or the right side of the manometer? b. The speed v2 of the fluid in the neck comes from measuring the difference between the heights (yR yL) of the fluid on the two sides of manometer. Derive an expression for v2 in terms of (yR yL), A1, A2, tube, and mano. FIGURE P15.52