An NPN bipolar junction transistor having VB > VE and Vc = (VB - 400 mV) is:Select one:O a. Operating in saturation.O b. Operating in deep saturation.O c. Operating in active mode.O d. Operating at the edge of soft saturation.In order to operate in the active mode. annpn transistor must have VBE 0 and VecSelect one:Tue

In this question we need to find the mode of operating region of the transistor.

An NPN bipolar junction transistor having VB > VE and Vc = (VB-400 mV) is: Select one: a. Operating in saturation. O b. Operating in deep saturation. c. Operating in active mode. O d. Operating at the edge of soft saturation.

An NPN bipolar junction transistor having VB > VE and Vc = (VB-400 mV) is: Select one: a. Operating in saturation. O b. Operating in deep saturation. c. Operating in active mode. O d. Operating at the edge of soft saturation.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a full-bridge dc-dc converter using PWM bipolar voltage switching, analytically obtain the value of (V/V) which results in the maximum (peak-peak) ripple in the output current i,. Calculate this ripple in terms of Va, La, and f
the slide is shown below. Explain how you think the model would look like if a transistor is in velocity saturation region?
Q16.Determine the Q point of the transistor circuit shown in the figure. Also draw the d.c. load line. Given β = 200 and VBE = 0.7V.
4. The band gap between conduction and valance band in an insulator is (Low Very low High Moderate) 5. Operating point of a transistor must be independent of (Biasing Amplification Variations in parameters Filtration) 6. When a transistor operating at the central of the load line is declining, the current gain will change the Q-point (down up nowhere of the load line) 7. A bipolar junction transistor when used as a switch, operates in (cut-off and active region active and saturation region cut-off and saturation region all of these) 8. Inversion layer in an MOS circuit is made by (doping impact ionization tunnelling electric field) 9. What are the applications of semiconductor devices? (Microprocessors Analog eircuits High voltage applications All of these)
Determine vo versus v₁ for the circuit shown in Figure 2. Assume that the MOSFET operates in saturation and is characterized by the parameters K and VT. Vs R₁ www Figure 2 wwww RL R₂ wwwww VO Note: assuming the MOSFET works at normal saturation regime and ips= (VDS -VT)²2 K 2
Question 1.1 (correcta) In the case of the circuit shown, it is a resistance that increases in value with increasing temperature. This type of thermistors are of the PTC (Positive Temperature Coefficient) type. Transistor Q1 is an N-channel enrichment MOSFET model HB-NR066, which has a threshold voltage VT= 3V, and turn-on values ID (on)= 10 mA and VGS(on)= 7V. The circuit It is used as a temperature-to-voltage converter for an industrial process, since the output voltage Vo changes with temperature. From the above, develop the following points.a) If it is known that at a temperature 50 degrees Celsius the value of the thermistor is RT= 5k Ω find the operating point of the transistor for this temperature, as well as the output Vo. Also, perform the necessary calculations to verify that Q1 is in the saturation zone.
Q2. a) In a Bipolar Transistor define the quantity a or hFB. How is the device structure of the npn Bipolar Transistor designed to maximize this quantity?
please quickly thanks !
A. Determine the VCE transfer as a function of Vi of the circuit in figure 1, (eliminating the zener diode), indicating the different areas of the transistor (Active zone VBE = 0.7v, VCEsaturation = 0.2v, VBSaturation = 0.8v; saturation zone: The transistor has a B = 110 and the reverse saturation current negligible. B. As in section a) with the zener diode, assuming that this is ideal, whose zener voltage is equal to 3.5Volts. R3=8K, R4=9K
Please all subpart is compulsory for like this please Asap
For the given circuit, Vcc = 19 volts, Rg = 900 KN, Rc = 8 KN, RE = 3 KN and B = 100. Assume Transistor is Silicon, VBE=0.7 volts. Vcc RC RB RE a. Compute for the base current Q-point, IBa (in Amperes) [ b. Compute for the collector current Q-point, Ica (in Amperes). c. Compute for the collector-to-emitter voltage, VCEQ (in Volts) d. Draw the Load Line, with details.'
Give the information below. Determine: 2 Given the emitter stabilized bias circuit, DC Equivalent Circuit Base Emitter Loop. Derive formula. Collector Emitter Loop. Derive determine. 1 2 20 V formula. 4 Solve the unknown values: 2.4 k2 a IB 510 k2 IcQ oVc b Ic VB VCE VCEQ B= 100 Vc IBQ VB e OVE f VE 1.5 k2