An M 14 x 2 hex-head bolt with a nut and a 14R washer under each of bolt head and the nut is used to clamp together two18-mm steel plates.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.Determine the bolt stiffness.The bolt stiffness kb is 592.69MN/m.

Step-3: kb=(153.9×7)+(115×26)153.9×115×207=653.48mMN…

Answered: An M 14 x 2 hex-head bolt with a nut…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

find the tensile of the bolt with diameter 38mm,80kN
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.
A 3-in Aluminum plate and a 2-in cast-iron plate are compressed with one bolt and nut. The bolt is 7/8 in-9 UNC. (1) Determine a suitable length for the bolt, rounded up to the nearest in. (2) Determine the bolt stiffness. (3) Determine the stiffness of the members.
A. PROBLEM ON TOPIC "KEYS AND COUPLINGS": A coupling with material AISI C1045 as rolled transmits 65.5 HP at 1750 rpm. The material of the 1.75 inch shaft... is also AISI C1045 as rolled and the key is cold drawn AISI C1020. N= 2.5. Determine the following: 1. Size of bolt (dia.) if there are 6 bolts made of AISI C1045 as rolled at a bolt circle of 5 inches. Note: Select standard bolt diameter from AT14 of DOME by Faires (see Lecture on fasteners for this Table) Calculated Dia: Standard Size to use: 2. Required b and t if a flat or rectangular key is used: Answer: 3. Required length of key, if a flat or rectangular key is used: Note: Calculate for two type of stresses on key, then select your answer. Length Based on shear length Based on compression: Length to use: 4. Required bif a square key is used: Answer: 5. Required length of key, if a square key is used: Note: Calculate for two type of stresses on kev, then select your answer. Length Based on shear length Based on compression:…
A 3/8-18 grade 8 bolt has 800 pounds of force pulling on it. Find the tensile force, the thread stripping strength for the needed length of engagement and the factor of safety for the bolt with that amount of force.
Ball bearings are rated by a manufacturer for a life of 106 revolutions. The catalogue rating of a particular bearing is 16 kN. If the design load is 2 kN, the life of the bearing will be Px 106 revolutions, where Pis equal to
A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
Use the drawing below to answer the following two questions. a. Determine the equivalent spring stiffness of the following system. Simplify the expression (ie – single common denominator. Your answer should be an expression of just K’s – no numbers). b. If the weight on top is 20 lb and the K1 = K4 = 50 lb/in, K2 = 33 lb/in and K3 = K5 = 25 lb/in, what is the natural frequency of the system?
A 2.5-in Aluminum plate and a 1.5-in cast-iron plate are compressed with one bolt and nut. The bolt is 3/8 in-16 UNC. (1) Determine a suitable length for the bolt, rounded up to the nearest 4 in. (2) Determine the bolt stiffness ks. (3) Determine the stiffness of the members km.
A 1000 mm cast iron pulley is fastened to a 112 mm shaft by means of a 28 mm squarekey 160 mm long. The key and shaft are SAE 1030 steel annealed with allowableshearing of key at 200 MPa and compressive of 660 MPa. a. What force in lbs acting at the pulley rim will shear the key?b. What force in lbs acting at the pulley rim will crush the key?
The length AB for the lug wrench shown below is 12 inches. What is the maximum force (F) that one can apply on the handles without yielding the material (Steel: Sy = 45 ksi). The diameter of the wrench is 0.625 inch. (Do not make any mistakes)
5. Determine the strength of a % in bolt having a yield stress of 60 ksi and stress area of 0.1134 in² 283 lbs 823 lbs 238 lbs 382 lbs

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS