An intersection approach has a saturation flow rate of 1500 veh/h, and vehicles arrive at the approach at the rate of 800 veh/h. The approach is controlled by a pretimed signal with a cycle length of 60 seconds and D/D/1 queuing holds. Local standards dictate that signals should be set such that all approach queues dissipate 10 seconds before the end of the effective green portion of the cycle. Assuming that approach capacity exceeds arrivals, determine the maximum length of effective red that will satisfy the local standards.

An intersection approach has a saturation flow rate of 1500 veh/h, and vehicles arrive at the approach at the rate of 800 veh/h. The approach is controlled by a pretimed signal with a cycle length of 60 seconds and D/D/1 queuing holds. Local standards dictate that signals should be set such that all approach queues dissipate 10 seconds before the end of the effective green portion of the cycle. Assuming that approach capacity exceeds arrivals, determine the maximum length of effective red that will satisfy the local standards.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need the answer quickly
An approach at a signalized intersection with a 60-second cycle gets 30 seconds of displayed green time. Yellow time is 4 seconds and all-red is 2 seconds (lost time is to be determined from standard assumptions). At the beginning of an effective red there are 4 vehicles in the queue and the saturation flow is 876 veh/h. The arrival rate is given by v(t) = 0.20 - 0.002t [with v(t) in veh/s and t in seconds after the beginning of the effective red]. What is the average vehicle delay for this approach in seconds at the end of the cycle (until the next effective red) that started with the 4 vehicles queued at the beginning of the effective red? (Assume D/D/1 queueing. Please provide you answer in decimal form without units)
Q4b. What are the relevance of the following considerations in traffic signal timing design? i. Incorporating all-red interval in the inter-green period ii. Conversion of all vehicle categories to passenger car units (PCU)
Problem-Traffic Engg. A two-phase signalized intersection is designed with a cycle time of 120 s. The amber and red times for each phase are 4 s and 50 s, respectively. If the total lost time per phase due to start-up and clearance is 2 s, the effective green time of each phase is s. (in integer)
A two-phase signalized intersection is designed with a cycle time of 100 s. The amber and red times for each phase are 4 s and 50 s, respectively. If the total lost time per phase due to start-up and clearance is 2 s, the effective green time of each phase is s. (in integer)
An observer notes that an approach to a pretimed signal, the time it will take the queue to clear after the start of the effective green (assuming that approach capacity exceeds arrivals and D/D/1 queuing applies) is 60 s. If the saturation flow rate is 1440 veh/h and the effective red time is 40 seconds, what is the maximum number of vehicles in a queue in a given cycle?
Compute the average approach delay per cycle, given the saturation flow rate of 2400 veh/h and is allocated 24 seconds of effective green in an 80-second signal cycle. Flow at the approach is 500 veh/h. Assume the traffic flow accounts for the peak 15-min period and that there is no initial queue at the start of the analysis period.
7.12 The saturation flow rate of an approach to a pretimed signal is 6000 veh/h. The signal has a 60-second cycle with 20 seconds of effective red allocated to the approach. At the beginning of an effective red (with no vehicles remaining in the queue from a previous cycle), vehicles start arriving at a rate v(t) = 0.4 +0.01t + 0.00057+² (where v(t)) is in vehicles per second and t is the number of seconds from the beginning of the cycle). 30 seconds into the cycle the arrival rate remains constant at its 30-second level and stays at that rate until the end of the cycle. What is the total vehicle delay over the cycle (in vehicle- seconds), assuming D/D/1 queuing?
A turning movement count and a saturation flow study were conducted at a major intersection on an expressway with configuration as presented in Fig.1. The peak-hour volumes and saturation flows obtained from the studies for each movement are presented in Tables 1 and 2, respectively. i) provide a diagrammatic representation of the signal sequence at the intersection. Assume a yellow interval of 3s, all-red interval of 2s and a peak hour factor of 0.95 for all the approaches. Note: No two movements should conflict during the determination of the phasing plan.
Vehicles arrive at an intersection approach at 550 veh/h at the beginning of an effective red and 15 vehicles are left in the queue from the previous cycle (end of the effective green). Due to peak hour congestion, the arrival rate increases 50 veh/h/min. Therefore after 1 minute, the arrival rate will be 600 veh/h, after 2 minutes it is 650 veh/h. The saturation flow rate of the approach is 1800 veh/h, the cycle length is 65 seconds, and the effective green time is 30 seconds. Determine the total vehicle delay until complete queue clearance. (Assume D/D/1 queuing).
(b) An approach to a pretimed signal has 25 seconds of effective green in a 60-second cycle. The approach volume is 500 vph and the saturation flow rate is 1400 vph. Calculate the average vehicle delay assuming D/D/1 queuing.
Subject: transportation engineering Read the question carefully and give me right solution according to the question. A signal has four phases, where the critical lane group flow ratios are 0.115, 0.204, 0.099, and 0.248. If the lost time per phase is 6 seconds and the critical intersection v/c ratio is 0.88, calculate the minimum cycle length and the phase effective green times such that the lane group v/c ratios are equal.