An insulated, electrically heated tank for hot water contains 190 kg of liquid water at 60°C when a power outage occurs. If water is withdrawn from the tank at a steady rate of =0.2 kg s-, how long will it take for the temperature of the water in the tank to drop from 60 to 35°C? Assume cold water enters the tank at 10 C, and negligible heat losses from the tank. For liquid water let Cy = Cp C, independent of T and P. %3D

An insulated, electrically heated tank for hot water contains 190 kg of liquid water at 60°C when a power outage occurs. If water is withdrawn from the tank at a steady rate of =0.2 kg s-, how long will it take for the temperature of the water in the tank to drop from 60 to 35°C? Assume cold water enters the tank at 10 C, and negligible heat losses from the tank. For liquid water let Cy = Cp C, independent of T and P. %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q3: A universal fractional horsepower series motor has a resistance of 30 22 and a total inductance of 0.5 H. When connected to a 250 V d.c. supply and loaded to take 0.8 A, it runs at 2000 r.p.m. Estimate the speed and p.f. when connected to a 250 V a.c. supply and loaded to the same current.
Quiq
chapter 1 Q1 The rms value the AC input voltage to the of Circuit shown is 230U, and the firing angle is maintained Current is 5 A. constant at 45° so that the load a) Calculate the de output voltage. b) Assume that the load resistance remains the a same, find the current is a FWD is used at the output. c) If^ prime prime ScR^ prime prime " is open circuited, find load voltage and current a is the Same) (FWD is still connected and high. "L Load Ans[146.4U,6.03A ; 3.c2A] 3 3 FWD
- Define the Zeroth law of Thermodynamic? -What is Energy? And Energy forms?
4. A copper wire has a length of 3500 ft and having an area of 144 cm squared. Find the resistance of the copper conductor at a temperature of 43ºC. 5. The power taken by a resistive coil made of copper wire is 1200W at 120V and 15 °C. Calculate the power consumed by the coil when connected at 250V and 110°C. The temperature coefficient at 27 °C is 0.00393 °C-1.
The diagram representa a primary coil P, carrying a steady current, and a secondary coil S,which is connected to a galvanometer G, The following steps are performed one after another: I. P is pushed rapidly into S II. P is held stationary inside S II, P is withdrawn rapidly from S IV, P is held stationary outside of S During which of these steps does G show a steady zero read Select one: a. II and III only b. II and IV only
I need the answer as soon as possible
Q3) how does the second law of thermodynamics was explained by KELVIN-PLANK and CLAUSIUS statement. Give a brief description.
what is the main difference between natural and forced convection
Q3\. A. Explain with sketches the operation of Digital phase meter. B. Why the dynamometer should be shielded and protected from any external magnetic fields? Q4 Calculate the value of the multiplier resistor for a 10 V rms ac range on the voltmeter in the figure. 10 V R₁ wwww Itsd = 1 mA R = 250 Q
In this Exercise 6 we will explore laws critical to the study of electromagnetism. We will be using Simulation 3 (below) to explore how a moving magnet produces current in a nearby coil of wire. a. Magnetic field strength decreases as you get farther from the poles of the magnet. Does the flux through the face of the coil change as you move the magnet? Explain your answer. b. Why does the meter needle deflect? Is the deflection in accordance with Lenz’s Law? Justify your answer in terms of Lenz’s law and your above answers.
4)