An infinite plate is moving at a constant velocity of 3m/s over a second stationary plate. A thin layer of the liquid with viscosity of 0.65 centipoises and specific gravity of 0.88 separates the moving plate from the stationary plate. The fluid velocity varies linearly with the distance from the stationary plate. If the length between the two plates is 0.3mm, determine: The absolute viscosity of the liquid in s                                     The kinematic viscosity of the liquid stokes       The shear stress on the fluid layer

Q: Assume a length of axon membrane of about 0.10 m is excited by an action potential (length excited =…

A:

Q: A water cooler uses 30 kg/h of melting ice to cool running water from 28 C to 5 C. Based on the…

A: Introduction  Using the heat energy equation, we will compute the logarithmic mean temperature…

Q: A liquid is entering a 10 m long pipe of 0.2 m diameter at 25°C with an average velocity of 0.02…

A:

Q: A steel beam, of lengths a=5 m and b= 3 m and a hollow box cross section, is supported by a hinge…

A:

Q: So first Draw the free body diagram Then second Find the Reactions Lastly Draw the Shear and Moment…

A: Draw the given diagram of the beam.

Q: A multimeter can NOT be used as; 1. Ohm meter. 2. Voltmeter. 3. Ammeter. 4. Transmitter. 5. Any of…

A: Since a multimeter is a device which can measure multiple electrical properties like voltage,…

Q: Determine the moment of inertia for this rectangle about: (a) The x-axis (b) The y-axis (c) Its…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: Consider the base plate of an 1200 W household iron with a thickness of L= 0.5 cm, base area of…

A:

Q: A fuel transportation industry uses a spherical 1045 carbon steel pressure vessel with a diameter of…

A:

Q: A 5 kg block is attached to a spring of constant k = 2400 N/m. The coefficient of friction between…

A: Given data:- mass of block= 5 kg spring constant k = 2400 N/m. The coefficient of friction between…

Q: *answer is correct To increase the rate of heat transfer from a device, which has 0.1 m² of exposed…

A:

Q: 18)draw the shear and moment diagrams with the equations for the beams and determine maximum shear…

A:

Q: For the horizontal series-parallel system of the figure below, all pipes are 7 cm diameter asphalted…

A: Given: d = 7cm ε = 0.12 mm ρ= 998 kg/m3 μ=0.001 kg/m.s Q= 0.0269 m3/s L.A = 250 m L.C = 150 m…

Q: The position of a particle in millimeters is given by s = 90-21t+t² where t is in seconds. Plot the…

A:

Q: An airplane flies at 400 mph at 1600 f altitude on a standard day. The plane climbs to 50,000 ft and…

A:

Q: The value of Henry's constant for 02 dissolved water at 300 K is 45,000 bar. Water is exposed to air…

A: Given: H=45000 bar=4.5×106 kPaxO2=0.2p=100 kPa

Q: 4. Draw the complete shear and bending moment diagrams. -2 m 15 kN. 20 kN m -1 m- -1 m- 10 kN/m -2…

A: Given,

Q: 7.30 5.90 4.50 Stress Lev 3.10 1.70 pox ഇന്നും 00 O 00 DO O XXOOD O OD 0 DOO 0 0 0 Оф COX0000000…

A: The intercept is calculated as the value of stress level at zero percentage From the given figure it…

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

A:

Q: Stress_Lev 7.30 5.90 4.50 3.10 1.70 .30 pox O 00 xoo .. ∞ 。。 O O O XXO XED ∞∞∞∞∞∞ . നാൽ സ -0.10 0.10…

A: Question 2   Here as shown in the graph the stress level is decreasing with the increase in the…

Q: Water flows normally through a 12 in pipe at the rate of 80 gal/min. at a point in the pipe an 8 in…

A:

Q: 3. Draw the complete shear and bending moment diagrams. -5 ft 800 lb-ft 5 ft 100 lb

A:

Q: Determine the natural frequencies and modal shapes of the system shown in figure to m1 = m2 = m and…

A:

Q: Which of the following methods of measuring IP value requires an assessment pay? O O of what the…

A: Cost-based IP valuation methods measure value by assessing the costs involved in creating and…

Q: The following are five different types of machoines 1. Pulley block  2. Lever 3. Worm and wheel…

A: Simples machines are very useful in our daily life. These machines lower the effort required to do a…

Q: This is a follow up to my question and the answer you submitted. The equation you used for J is…

A: According to question:- Outer radius of pipeR=50mm⇒Outer diameterD=2R=100mm=0.1mInner radius of…

Q: W COMP. IN = 6700kW COMPRESSOR Ⓒ₁ AIR DE T1= 26.85°C P1= IBAR QUES πίσω PS = PA Ⓡ T2 = 346.85 °C P2…

A:

Q: Please write neatly and show all work and explanation So first Draw the free body diagram Then…

A:

Q: Determine the weight in newtons of a car which has a mass of 1490 kg. Convert the given mass of the…

A: Given data:- The mass of the car (m) = 1490 kg Determine:-    The weight of the car (W) in N    The…

Q: A column in the Museum Göttingen is formed by identical boards glued together, as shown in the…

A:

Q: Water at 60°F and one atmosphere is being transferred from tank 1 to tank 2 with a 2-hp pump that is…

A: As per the guidelines I can solve only first three subparts. Repost the other part.

Q: A long counter-flow heat exchanger cools water from 40°C to 10°C by passing the water via the inner…

A:

Q: A 8.0 m long ladder AB leans against a smooth wall making an angle of 70º with the floor. The ladder…

A: Given:Length of the ladder, l=8 mAngle made with the floor, θ=70°Mass of the ladder, m=40 kg

Q: 12)draw the shear and moment diagrams with the equations for the beams and determine maximum shear…

A:

Q: Which of the following methods of measuring IP value requires an assessment of what the customer…

A:

Q: Problem 5 s): The discharge pressure (P) of a screw pump (Fig. 5) is a function of flow rate (Q),…

A: Variables are flow rate, screw diameter, fluid viscosity and screw angular speed. Repeating…

Q: Air having a density of 1.27 kg/m³ enters the inlet of an engine at a rate of 1000 m³/sec of a…

A:

Q: Water runs through a water main of cross-sectional area 0.5 m² with a velocity of 8 m/s. Determine…

A:

Q: Ta-1.2 kN-m 40 mm LEGGG 54 mm T-0.8 kNm 46 mm T-0.4 kN m 40 mill ASSIGNMENT 2.6 Under normal…

A:

Q: 2 m B 6 m- 6 m 2 m -10 m- 6 m 4 m 12 m 2 m y GIVEN: PLATE MASS IS 150KG ASK: WHAT IS TENSION OF EACH…

A:

Q: Required information Problem 13.056 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is…

A:

Q: Q.7) Water (μ= 1cP) flows upwards through the smooth pipe (d-2 cm) at 0.6 m/s (see drawing).…

A: Given:Dynamic viscosity of water, μ=1 cP=0.001 N.s/m2Pipe diameter, d=2 cm=0.02 mWater velocity,…

Q: The purpose of a patent fence is to block rivals from operating in a particular technology space.…

A:

Q: In membrane processes the _____ ____ mode of operation has the feed water flowing tangentially to…

A:

Q: "Your boss requests a recommendation on which process to use to make fillet welds on stainless steel…

A: GMAW is a welding technique in which metals are joined by heating the metals to their melting point…

Q: Find the centroid of the composite area shown below. O 0.75 in. 10.375 in. 1.5 in. Suyd

A: Given question is related to mechanics.

Q: 2a y 1 - 2a a -2.5a 7a 2a 1.5a ---X

A:

Q: Outside air at -7°℃ and relative humidity of 60%, infiltration air enters the conditioned room at…

A: Given: T1=-7oC φ1=60% V˙=60 m3/hr φ3=40% T3=18oC

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm and a…

A:

Q: K ANA DE F C B -2 m--2 m--2 m--2 m--2 m--2 m- 20 KN 30 KN 40 kN 3 m H G Find the Internal Force in…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.