An excessive voltage drop in a circuit may cause undesired drawbacks. Within your own home, state TWO (2) real examples of voltage drop impact. (motors running slowly, heaters not heating to full potential, lights being dimmed) Q2 (a) A single-phase 240V branch circuit with length of 0.092 km comprising of # 4 AWG THW aluminium conductor with steel conduit. If load current is 12Z-30°A, obtain the voltage drop along the circuit. (b)

An excessive voltage drop in a circuit may cause undesired drawbacks. Within your own home, state TWO (2) real examples of voltage drop impact. (motors running slowly, heaters not heating to full potential, lights being dimmed) Q2 (a) A single-phase 240V branch circuit with length of 0.092 km comprising of # 4 AWG THW aluminium conductor with steel conduit. If load current is 12Z-30°A, obtain the voltage drop along the circuit. (b)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.56P: Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit...

See similar textbooks

Similar questions

Q2. The single-line diagram of a simple three-bus power system is shown in Figure-2. Each generator is represented by an emf behind the sub-transient reactance. All impedances are expressed in per unit on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A three-phase fault occurs at bus 3 through a fault impedance of Zf = j0.19 per unit. (i) Using Th'evenin's theorem, obtain the impedance to the point of fault and the fault current in (ii) Determine the bus voltages per unit. ) j0.05 j0.075 j0.75 2 j0.30 j0.45 Figure-2: Single line diagram of the power system network for Q2 3
Voltage sags due to short circuit and earth faults are the cause for the vast majority of equipment problems. Electronics equipment become more susceptible to voltage sag, hence the companies experience production stoppages. Voltage sag analysis is very complex issue. Based on voltage sag randon factors describe on it.
A circuit breaker is rated as 132 KV, 4000 MVA. What will be the Asymmetrical breaking current capacity if DC component is assumed to be 70% ?
Answer all the questions 1. Draw a 6-stage cascaded voltage multiplier circuit for high voltage DC generation and explain the working principle. 2. Compare the properties of Solid insulators and liquid dielectrics? 3. Define Basic Insulation Level (BIL) in power systems and Explain the voltage - time relationship with the curve in insulation coordination. 4. What are the three protective methods for surges, explain one method. 5. What are the different types of surge diverters and explain any two methods? 6. A 12-stage impulse voltage generator has a total generator capacitance of C1. The wave front resistance equal to 15000 2 and load capacitance of 2500pF. The wave tail resistance is 30 times of wave front resistance and if rise time is 1.5 µs. Calculate (i) the value of each capacitor of the generator and (ii) the tail time of the impulse wave?
A. Discuss the arcing phenomenon in a circuit breaker. B. Discuss the types of oil circuit breakers. With references
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
pure dc will have ____ ripple
Discuss causes of insulation failures in high voltage engineering. High voltage engineering
Equal area criteria is a method used to calculate: Select one: O a. None of the answers b. Critical clearing angle and time for transient faults O c. Critical clearing voltage angle for transient faults d. Transient stability current limit O e. Steady state stability power limits
13.a. Eddy-current loss in the stator core can be reduced by usingA. alloys with low resistivity.B. annealed iron laminations.C. silicon alloys of copper.D. thin laminations of steel.13.b. Which one of the following is damaging to many insulating materials used in alternators?A. Eddy currentsB. SaturationC. CoronaD. Hysteresis
Q-5-) 60 Hz generator supplies 0.50 Pmax power to a busbar with infinite power over a conveying line. When a fault occurs, the reactance value between the generator and the infinite bus becomes 400% times the value before the fault. When the fault is isolated, the maximum power that can be transferred generator to the endless bus is 75% of the original (initial) maximum value. Accordingly, using t area criterion method, calculate the critical clearance angle of the system. 00
b) A fault occurs at bus 3 of the network shown in Figure Q4. Pre-fault nodal voltages throughout the network are of 1 p.u. and the impedance of the electric arc is neglected. Sequence impedance parameters of the generator, transmission lines, transformer and load are given in Figure Q4. V₁ = 120° p.u. V₂ = 120° p.u. V₂ = 1/0° p.u. V₂= 120° p.u. jXj0.1 p.u. JX2) 0.1 p.u. jX0j0.15 p.u. jXn-j0.2 p.u. 1 JX(2)-j0.2 p.u. 2 jX)=j0.25 p.u. JX20-10.15 p.u. jXa(z)-j0.2 p.u. 4 jX2(0)=j0.2 p.u. jXT(1) j0.1 p.u. jXT(2)=j0.15 p.u. jXT(0)=j0.1 p.u. Figure Q4. Circuit for problem 4b). = jXj0.1 p.u. j0.1 p.u. - JX(2) JXL(0) 10.1 p.u. = (i) Assuming a balanced excitation, draw the positive, negative and zero sequence Thévenin equivalent circuits as seen from bus 3. (ii) Determine the positive sequence fault current for the case when a three- phase-to-ground fault occurs at bus 3 of the network. (iii) Determine the short-circuit fault current for the case when a one-phase- to-ground fault occurs at bus…