Answered: An engine develops 450 N m of torque at…

Science

Physics

An engine develops 450 N m of torque at 3500 rev/min. Find the power developed by the engin

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Dynamics

Section8.4: The Rotational Second Law Of Motion

Problem 8.1QQ: Using a screwdriver, you try to remove a screw from a piece of furniture, but cant get it to turn....

See similar textbooks

Related questions

Q: A businessman enters a revolving door on the right, pushing 576N of force directed perpendicular to…

A: Force applied by businessman: F1 = 576 N Perpendicular Distance of force by businessman from hub: d1…

Q: is supported against the wind by a rope tied to a stake in the ground, as shown in the figure below.…

A: Given:- F = 119 N, D = 2.42 m d = 1.02 m Find:- Find the tension in the rope.

Q: 10 N .5 m A force is applied on a pulley as shown above. What is the torque (in unit of N'm)…

Q: When opening a door, you push on it perpendicularly with a force of 55.0 N at a distance of 0.850 m…

A: Given F = 55 N, distance is r = 0.850 m. Force is perpendicular so angle is 900

Q: A rod is pivoted about one end. Two forces F → and − F → are applied to it. Under what circumstances…

Q: find the magnitude of the torque exerted by F on the bolt at P if |PQ| = 8 in. and |F| = 30 lb.…

A: Given that, |PQ| = 8 in= 0.667 ft |F| = 30 lb

Q: A truck can produce 450 lbsfeet of torque. If the drive wheels have a diameter of 20.5 inches, and…

A: Given:torque, τ = 450 lbs feetdiameter of wheel, d = 20.5 inches weight of truck, W = 3500 lbs

Q: The right hand screw rule does not involve

A: Solution

Q: how to balance this using torque balance (F )(4 m) = (120N) (3 m)

Q: If you are trying to loosen a stubborn screw from a piece of wood with a screwdriver and fail,…

A: Opening a screw

Q: A brake is applied to the rim of a wheel with a force of 2.50 kN and the coefficient of friction…

A: Given: The applied force on th rim is 2.5 kN. The coefficient of the friction is 0.4.

Q: In opening a door, a 34.0 N force is applied as shown in the figure below. Find the torque produced…

Q: The force applied tangentially to a bar of a screw-jack at a radius of 250 mm, if the torque…

A: Given Torque T=12 kNm radius r=250mm=0.250m

Q: A force of magnitude 74 N is applied to a door. The lever arm is given at 0.875 m. Find the torque

A: Given Magnetic of force is F=74 N Lever arm is l=0.875 m

Q: Compute the torques produced by the following forces. Be sure to indicate whether the torque action…

Q: hinge

A: The given data are: m=2.13 kgb=1 mF=162.8 Nθ=61°r=0.481 m

Q: The product of the applied torque and the length determines the relative angle of twist between the…

Q: The boom of a crane is 19.56 m long and is inclined 28.4 degrees from the horizontal. A bucket of…

A: L= 19.56 m Angle is 28.4° M= 3292.29 kg

Q: What kind of force can be acting on an object in equilibrium? Select one: O a. balanced b.…

A: Correct Answer : If an object is at equilibrium , then the forces are balanced .Balanced is the key…

Q: A rope te wound around a shaft 10cm in diameter. If a pull of 500N is exerted on the rope, what…

A: Torque imparted to the shaft = Force × perpendicular distance from the axis about which the rod will…

Q: When the palmaris longus muscle in the forearm is flexed, the wrist moves back and forth. If the…

Q: A rod of Length 5R is fixed about a point 1/5th of the length from the right edge. All forces are…

A: In given figure 4 forces are applied on rod at different point. Torque = r × F = perpendicular force…

Q: The engine of the bus applies a torque of 361.5 N · m to a wheel of radius 0.273 m. Since the wheel…

Q: A 1 530-kg automobile has a wheel base (the distance between the axles) of 2.80 m. The automobile's…

A: Given Data : The mass of the automobile is given as m = 1530Kg. The wheelbase is given as d = 2.80m.…

Q: A force of 618.8 N is applied at the end of a wrench of length 145.2 cm. Find the torque produced in…

A: The torque can be expressed as τ=r×F

Q: A hollow, spherical shell with mass 3.00 kg rolls without slipping down a 39.0 ∘ slope. (a)Find the…

Q: A force of 6.8 N is applied to a door at an angle of 50.0o and a distance of 0.75 m from the hinge.…

A: Force=6.8N r=0.75 Theta=50 degree

Q: A worker applies a torque to a nut with a wrench 0.500 mlong. Because of the cramped space, she must…

Q: A uniform beam of weight 12 N and length 10 m is mounted by a small hinge on a wall. The beam is…

Q: The crank arm of bicycle pedal is 16.5 cm. If a 52kg woman puts all her weight on the pedal, how…

Q: A bowl is rotating on a potter's wheel at constant angular speed as shown. The friction force…

Q: A force of 290 N acts tangentially on the rim of a wheel whose radius is 25 cm. Find the torque…

A: Tangential force applied F = 290 N radius of rim r = 25cm= 0.25 m

Q: A hollow, spherical shell with mass 3.00 kg rolls without slipping down a 35.0 degree slope. a) Find…

Q: A train, traveling at 66 mi/h, rounds a horizontal curve of 390 ft radius. A passenger standing in…

Q: 16. A wheel of mass M and radius R rests on a horizontal suface against a step ofheight h (h<R). A…

Q: How to find net torque?

A: torque

Q: Explain how to find the torque produced by a force using cross products.

A: Torque Torque is the rotational equivalent of force. To make a body move linearly we apply force…

Q: A certain screw jack has a pitch of 5mm and mean diameter of 180mm. The coefficient of friction…

A: Given parameters, Pitch, p = 5mm = 5×10-3m Diameter =180mm, So, radius r=90mm = 90×10-3m…

Q: A rectangular bar is hinged at point O. The bar is 3.00 m long and 2.00 m wide. Find the torque…

A: It is known that, F1=1N Length of bar, l=3 m Width of bar, w=2 m

Q: Establish the 2nd condition of equilibrium (rotational equilibrium) using A. Point A as the pivot…

A: Solution:-

Q: 4. Three forces are acting on a rectangular block of wood as shown, with a pivot in the lower-left…

A: GivenThree forces are acting on a rectangular block

Concept explainers

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.

Question

An engine develops 450 N m of torque at 3500 rev/min. Find the power developed by the engine.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

An engine has torque of 550 Nm at 8.3rad/s . What power in watts does it develop?
An automobile engine develops a torque of 600 N*m at4000 r/min. What is the horsepower of the engine?
A screwdriver turns a screw an angle of 5.09 radians by applying a torque given by (in Nm) T=1.57 + 6 Calculate the work done, W by the torque. Enter W, measured in Joules, correct to three significant figures:
A rod of length Lis held upright and pivoted on the floor and then dropped. Find the speed of the other end when it hits the ground. a
A single-cylinder reciprocating engine has a reciprocating mass of 6 kg. the crank rotates at 60 rpm and the stroke is 32 mm the mass of the revolving parts at 16 mm radius is 4 kg, if two-thirds of the reciprocating parts and the whole of the revolving parts are to be balanced. Determine the balance mass required at a radius of 35 mm and unbalanced force when the crank has turned 50° from the TDC.
An engine starts at 100 rad/s of angular velocity and uniformly accelerates to 400 rad/s in 9.5 s. Find the total angle rotated during this time, in rad. Hint: use rotational kinematics formula. Assume initial angle as zero.
11. A 20N force is applied at the end of a wrench that is 40 cm. in length. The force is applied at an angle of 60o to the wrench. Calculate the magnitude of the torque about the point of rotation M. The answer here is 6.93J. Please give processes.
A 10 kW motor developing a torque of (200/π) N m is running at a speed of:
The torque that a motor develops depends on the rotation rate of its drive shaft according to τ(ω) = 137 - 13ω (N m), where the angular velocity is measured in rad/s. What is the maximum power output of this engine, in W? (Please answer to the fourth decimal place - i.e 14.3225)
A torque of 170 N.m does 3036 J of work on a rotating flywheel. If the flywheels initial kinetic energy is 1637 J, what is its final kinetic energy? Report your answer in 4 significant figures Answer:
Output is 150kW at 5000rev/min, what is the torque?
A and B shafts enter the wheel link gearbox of a tractor and are connected to the engine with the C shaft. A and B is in the vertical yz plane, while the C shaft is in the x-axis direction. Pairs with a single equivalent pair replace