An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 0.5 m depth.   a.393.9 b.3.9 c.63.0 d.17.8

Q: combined stresses for the

A:

Q: Fig structure carrying weight. The uniform bar AB weighs 1.1.4.4 shows a 300 N and carries a 500 N…

A:

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

A:

Q: Given data Tensile force=D30 KN Rectangular section width=5 m Depth =10 m Determine stress

A: Given data, Tensile force= F = 30 KN = 30000 N Rectangular section width=b =5 m Depth =h =10 m…

Q: At a point in a vertical cross-section of a beam there is a resultant stress of 75 MN/m2 , which is…

A: Given-At a point in a vertical cross-section of a beam there is a resultant stress of plane is…

Q: Compute the maximum shearing stress at A in MPa. b. Compute the maximum shearing stress at B in…

A:

Q: The homogeneous bar ABCD shown in the figure below is supported by a cable that runs from A to B…

A: The stress in cable is The area of cable AB is The area of cable at C is Point D is smooth

Q: center of a square uniformly (a-6m and z=3.75m). Usin

A: The lagrange's formula is as,fx = x-x1x-x2x-x3x-x4x0-x1x0 -x2x0-x3x0-x4×yo+x-x0x-x2x-x3x-x4x1-x0x1…

Q: An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The…

A: Option d is correct.

Q: 1. The rigid link ABC is supported by a pin at B (which is connected in double-shear) and a steel…

A: ◆ First of all, calculate tension developed in the wire CD by taking moment about point B. ◆ The…

Q: A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a…

A: Given:The outer diameter of cylinder is .The inner diameter of cylinder is .

Q: A hollowed circular clinder carries an axial force of 100 KN. Find the inner diameter if the…

A:

Q: A state of stress at a point A is given by ox = 50 MPa, oy = -25 MPa, and txy = -100 MPa. What is…

A: Please see the below explanation;

Q: 6. Refer to figure 2. Bar АВCD with cross-sectional FIGURE 2 area equal to 600 mm?. Determine the…

A:

Q: A 4-ft diameter spherical tank is subjected to an internal pressure of 34 psf. If the wall thickness…

A:

Q: 41.)  A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is…

A:

Q: A thick-walled pipe should be mounted in the space between a shaft and a wreath....

A: Given-Data:- Inner Radius =aOuter Radius =2av=1/2 To-Find:- Tension

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each…

A:

Q: a unity. If you know that diameter of bolts 10 mm and it's allowable shear stress is 26 kN/m

A: FREE BODY DIAGRAM-   ΣMA=012×26×4×83-RB×8=0RB=17.333KNΣFY=0RA+17.3333-12×26×4=0RA=34.6667KN So that…

Q: A circular cylinder with inside diameter of 10 cm which carries a compressive force equivalent to…

A: Inside diameter of the cylinder, Di=10 cm=100 mmCompressive force, F=400000 NAllowable stress,…

Q: Find the height to be raised P.E=2442.11J

A: Given data : m=Mass g=Acceleration due to gravity P.E=Potential energy   Required : height to be…

Q: Q2. For the given cube below, draw the Mohr's circle and find stress on th horizontal and vertical…

A: The stress on plane rotated by 45° is

Q: 2. The homogeneous 1000-lb plate is suspended from three cables. Determine the smallest diameter…

A:

Q: From 3 forces, 2 bending moments and 1 toque acting on B, which ones are non zero, and the direction…

A: free body diagram

Q: A thin wall spherical tank of diameter 1.5 m and wall thickness 65 mm has internal pressure of 20…

A:

Q: Using the figure and loadings given, find the forces in all members, then find the average normal…

A:

Q: Find stress in each segment. Diameter of AB is 2in and diameter of BC is 1in.

A:

Q: A building weighing 100,000 Ibs is placed on the L-shaped slab shown. The soil below the basement is…

A: We know that, x=A1x1-A2x2A1-A2 A1=80×60=4800 ft2x1=802=40'y1=602=30' A2=50×20=1000…

Q: 1. For o= 150 MPa and o= 20 deg, the normal stress on inclined plane AB is best given by 145 MPa-…

A:

Q: 7.5 Refer to Figure 7.13, which shows a flexible rectangular area. Given: B₁ = 1.22 m, B₂ = 1.83 m,…

A: Given:To find:

Q: 5. A cylindrical pressure vessel has an inner diameter of 240mm and a wall thickness of 1.5mm. If…

A:

Q: 8.23. The plan of a flexible rectangular loaded area is shown in Figure 8.25. The uniformly…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.