An electric motor (with an efficiency of n1 = 90%) drives a belt (n2 = 85%) that is connected to a generator (n3 = 92%) that produces electricity for an incandescent ligl (n4 = 5%). Improving the efficiency of this part would greatly increase the overall system efficiency: O The Incandescent Light O The Belt O The Generator O The Electric Motor

An electric motor (with an efficiency of n1 = 90%) drives a belt (n2 = 85%) that is connected to a generator (n3 = 92%) that produces electricity for an incandescent ligl (n4 = 5%). Improving the efficiency of this part would greatly increase the overall system efficiency: O The Incandescent Light O The Belt O The Generator O The Electric Motor

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a) Exciting current (ii) Ic (b) Magnetizing Current (iii) Ie (c) core loss current
20. The resistance R and a 2 μF capacitor are connected in series across 200-V dc supply. Across the capacitor is a neon lamp that strikes at 120 volts. Calculate the value of R to make the lamp strikes 5 seconds after the switch has been closed. A. 4.89 kΩ B. 4.89 MΩ C. 2.73 MΩ D. 2.94 MΩ
f) To what voltage the machine will cxcite when the field resistance is 55 and the speed 800 rp.m. ? 05 1. Field current (A) 10 50 100 175 4 EMF () 220 245 262
Question 4 a) B M Figure 4 Figure 4 shows the graph of the ripple current. Answer the following i. Describe the function of A. ii. iii. Describe the function of B. Identify the ideal paramater to get the good power supply.
Calculate the resistance of the field coil. Show your calculations results table incase needed(don't think it is for this question)- Field current (If) flux density(B) in mT 0 0.01 0.25 0.11 0.50 0.20 0.75 0.29 1.00 0.36 1.25 0.40 1.50 0.43 1.75 0.45 2.00 0.47
Electric machines2
Introduction Explanation of Maximum Power in DC
Calculate the peak voltage across R2 in the diagram R1 = 1 kohm, R2 = 680 ohms, supply voltage is 10V RMS 5.73V peak 10V peak 4.04V peak 1.75V peak
The efficiency of any real wind turbine O a. can be more than 59.3% O b. can be less than 59.3% O c. is nearly 100% O d. is always equal to 59.3%
b. A piece of pencil lead is connected in series with an ammeter and a power supply. The power supply is turned on. After a few minutes, although the potential difference across the pencil lead does not change, the current in the circuit increases significantly. Explain why the current increases. c. Electric fields are caused by both point charges and by parallel plates with a potential difference across them. Describe the difference between the electric field caused by a point charge and the electric field between parallel plates. Your answer should include a diagram of each type of field and reference to electric field strength. Question 2
A rubber rod is rubbed with fur, so that the fur becomes positive. The rod is then used to charge an electroscope. The charge on the electroscope will be:positive if charged by contact. neutral. positive if charged by induction.negative if charged by induction.
Coulombs law