
Concept explainers
An athlete with a mass of 50.0 kg is doing pushups as shown in the figure below. The value for rW⊥ is 0.95 m and the value for rR⊥ is 1.56 m.
(a) Assuming she moves upward at a constant speed, determine the force she must exert on the floor with each hand to do a push-up. ______ N
(b) The triceps muscle in the back of her upper arm with an effective lever arm of rT⊥ = 1.60 cm, as shown in the figure below, and she exerts force on the floor a horizontal distance of r 'R⊥ = 1.95 cm from the elbow joint. Determine the force in the triceps muscle. ______N
(c) In order to appreciate the strength of the triceps, determine the ratio of the force in the tricep muscle to her weight (in decimal form). FT/W = _____



Trending nowThis is a popular solution!
Step by stepSolved in 4 steps

- The support shown below is connected to a control cable at point B and has a joint at C. For the loads shown, determine the magnitude of the reaction at the support at point C when: d1 = 0.19 m d2 = 0.25 m d3 = 0.49 m d4 = 0.47 m F1 = 263 Narrow_forwardThe upper leg muscle (quadriceps) exerts a force of FQ = 1140 N, which is carried by a tendon over the kneecap (the patella) at the angles shown in the figure below. Find the magnitude in newtons and direction in degrees counter-clockwise from an axis directed to the left of the force exerted by the kneecap on the upper leg bone (the femur). magnitude ______ N direction _____ ° counter-clockwise from an axis directed to the leftarrow_forwardConsider the 63.6-kg mountain climber in the Figure below. Assume the given angle of the rope from the rock wall is 33.5 degrees instead of 31 degrees; likewise assume the angle of the climbers legs from vertical is 11.4 degrees instead of 15 degrees. Find the force that the mountain climber must exert with her feet in pounds on the vertical rock face to remain stationary. Assume that the force is exerted parallel to her legs. Also, assume negligible force exerted by her arms. 31 15 Type your answer...arrow_forward
- Three cables are used to tie the balloon shown in Figure. Determine the magnitude of the vertical force (P) exerted by the balloon at A, knowing that the tension in cable AD is 954 N. y1 = 4.4 m y2 = 2.2 m x1 = 4.2 m x2 = 3 m z = 6 marrow_forwardA crate that has a mass of 65.1 kg is held in equilibrium by two ropes as shown in the figure. Find the tension (in Newtons) in rope 1 if a = 33.2 0.arrow_forwardFind the mass m of the counterweight needed to balance a truck with mass 1500 kg on an incline of 0 = 45 degrees. Assume both pulleys are frictionless and massless. Marrow_forward
- A window washer is standing on a scaffold supported by a vertical rope at each end. The scaffold weighs 202 N and is 2.8 m long. What is the tension in each rope when the 706–N worker stands 1.20 m from one end? SMALLER TENSION= _______N LARGER TENSION= ________Narrow_forwardThe 1.0 kg block in (Figure 1) is tied to the wall with a rope. It sits on top of the 2.0 kg block. The lower block is pulled to the right with a tension force of 20 N. The coefficient of kinetic friction at both the lower and upper surfaces of the 2.0 kg block is μk= 0.43. For general problem-solving tips and strategies for this topic, you may want to view a Video Tutor Solution of Car on rolling board. What is the acceleration of the 2.0 kg block?arrow_forwardEstimate the maximum tension T in the cable that supports a typical elevator. ?= Narrow_forward
- The image below depicts the Apollo 16 Lunar Module (LM) on the moon's surface. The diagram to the right is a model of one of the four landing gear assemblies. Determine the force supported by members AB, AC, and AD under the assumption that the weight of the LM is uniformly distributed by all four landing gear assemblies. Use Mathematica or an online calculator such as the WolframAlpha 3 Equation System Solver to solve the 3 x 3 system of equations that you will end up with. Z NASA X A (2.5, 2.5, -2.2) m B (1.5, 1.5,0) m C(2, 1,-1.2) m D(1,2,-1.2) m B Darrow_forwardSuppose you have a stack of 17 identical steel bars (steel bars have a mass of 1.00kg each). You are required to pull out bar number 16 from the stack (counting from the top of the stack down). Assuming that your assistant holds all other bars in place. If the coefficient of friction between steel and steel is 0.750, how hard do you have to pull (in N)?arrow_forwardA typical jar that has been tightened to a reasonable degree requires 2.0 N ⋅ m to open. If you grab a 7.0-cm-diameter jar lid with one hand so that your thumb and fingers exert equal magnitude forces on opposite sides of the lid, as shown, what is the magnitude of each of the forces?arrow_forward
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics (14th Edition)PhysicsISBN:9780133969290Author:Hugh D. Young, Roger A. FreedmanPublisher:PEARSONIntroduction To Quantum MechanicsPhysicsISBN:9781107189638Author:Griffiths, David J., Schroeter, Darrell F.Publisher:Cambridge University Press
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningLecture- Tutorials for Introductory AstronomyPhysicsISBN:9780321820464Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina BrissendenPublisher:Addison-WesleyCollege Physics: A Strategic Approach (4th Editio...PhysicsISBN:9780134609034Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart FieldPublisher:PEARSON





