An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 900Hz. If the system is operated at a bit rate of 180kbps and each input sample is quantized into 1024 levels, answer the following: a) What must be the minimum sampling frequency to avoid aliasing? samples/sec b) What is the Nyquist rate? c) What must be the number of bits per sample? kHz Hz bits d) If the sampling frequency is 10% above the Nyquist rate, what is the Nyquist frequency?

An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 900Hz. If the system is operated at a bit rate of 180kbps and each input sample is quantized into 1024 levels, answer the following: a) What must be the minimum sampling frequency to avoid aliasing? samples/sec b) What is the Nyquist rate? c) What must be the number of bits per sample? kHz Hz bits d) If the sampling frequency is 10% above the Nyquist rate, what is the Nyquist frequency?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- A music signal has frequency content from 0 Hz up to 8.75 kHz. (a) What sampling frequency must be exceeded for successful A/D conversion? (b) What is another name for the minimum sampling frequency?
Choose the correct answer low HDOP (Horizontal Dilution of Precision) number such as2 indicates a ........................... a.poor fix b.good fix c.poor signal quality d. good signal quality
An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz. The quantization error in any one sample value must be within ± 0.5% of the peak-to-peak amplitude range of the ADC. How many binary digits must each sample contain? Apply (or equate) the formulas:Δ = Xmax - Xmin / L - 1where Xmax - Xmin = peak-to-peak amplitude range (XRange)eq[n] = Δ/2 (maximum quantization noise)eq[n] = 0.005 XRange
1. With the help of Octave program perform the Modulation and Demodulation (AM) of information signal with carrier signal, through subplots with following signals a. Modulating signal b. Modulated signal c. Demodulated signal
Pulse-code modulation (PCM) is the standard form of digital audio in computers, compact discs, digital telephony and other digital audio applications. Figure 3 shows the 3bit PCM system that transmit the 250 kHz analog signal with the voltage range from -6 mV to 6 mV. i) Identify the quantized value, voltage range and binary code for each level by building your own quantization table. ii) Calculate the minimum sampling rate and sampling time. ii) Identify the corresponding sampled voltage, the quantized voltage and binary code if the input signal is sampled at time t1 = 2us, t2 = 4us, t3 = 6us, t4 = 8µs. iv) Sketch the output in (iii) if it is fed to Manchester coding line encoder with bit rate of 20000 bit/sec and amplitude of +4 V. 5 4 3 2 10 Timel(usec) Figure 3 Amplitude (mV)
MCQ) 5)Quantization error------: a. decreases as the bits per sample increases b. decreases as the bits per sample decreases c. decreases as the sample rate increases d. decreases as the sample rate decreases 6)The difference between the actual value of the sample and the quantized value of the sample is called: a. PAM error b. Sampling error c. Quantization error d. PCM error ThESE multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer.
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?
The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of : 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 43 Hz and an amplitude range of - 10 to 10 Vots. Determine the minimum bit rate fin bps) required in the PCM system? O a 688 O 774 O c 387 O d 86 Oe 258
1.) Determine the bit rate and quantization step of the ADC in the sampling of analog signal with x[n] of 1.02 Vpp, sampling rate of 20 samples per second, and 8-bit binary code 2.) An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz. The quantization error in any one sample value must be within (plus-minus sign) 0.5% of the peak-to-peak amplitude range of the ADC. How many binary digits must each sample contain?
An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 900Hz. If the system is operated at a bit rate of 180kbps and each input sample is quantized into 1024 levels, answer the following: a) What must be the minimum sampling frequency to avoid aliasing? samples/sec b) What is the Nyquist rate? c) What must be the number of bits per sample? kHz Hz bits d) If the sampling frequency is 10% above the Nyquist rate, what is the Nyquist frequency?
I would be very happy if you solve the question of this signal processing issue quickly.
[0 5] the signal in the volt range will be quantified. since n=4; a)Calculate what is the number of Qunta levels? b) Calculate what is the quantization interval? c)V=3.2 volts rounded to what quantization level? Let's draw with Quantalama level chart