3An aluminum stepped shaft (E = 10 × 10³ ksi, v = 0.35), is subjected to three axial forces as shown.For P1= 100 lb, P2 = 128 lb, P3=386 lb,L1=2.5 in, L2= 2.0 in, L3= 1.0 in,determine the elongated/shortened length of section CD. [106 in] (sign sensitive)1.5 in.DICL;1 in.BP₂0.5 in.L₁A₁ P₁

The young modulus of the aluminum shaft, The forces,The length of the section CD, The diameter of…

An aluminum stepped shaft (E For P1= 100 lb, P2 = 128 lb, L; L1= 2.5 in, L2= 2.0 in, L3 = 1.0 in, determine the elongated/shortened length of section CD. [106 in] (sign sensitive) 1.5 in. 1 in. L₂ B P3 = 386 lb, 10 × 10³ ksi, v = 0.35), is subjected to three axial forces as shown. P₂ = 0.5 in. A₁ P₁

An aluminum stepped shaft (E For P1= 100 lb, P2 = 128 lb, L; L1= 2.5 in, L2= 2.0 in, L3 = 1.0 in, determine the elongated/shortened length of section CD. [106 in] (sign sensitive) 1.5 in. 1 in. L₂ B P3 = 386 lb, 10 × 10³ ksi, v = 0.35), is subjected to three axial forces as shown. P₂ = 0.5 in. A₁ P₁

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
2. A steel shaft rotating at 600 rpm is supported by two bearings as shown. E=30 Msi, d=1.0" (inch), L₁=24.0" (inches), L=42" (inches), W₁-50 lb, Neglect the weight of the shaft. "The design is acceptable." True ? Show details. or False Diameter d W₁
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
A compound steel [G= 94 GPa] shaft consists of solid 28-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 68 mm and an inside diameter of 63 mm. Assume L₁-0.2 m, L₂-2.2 m, L3-0.2 m and T-210 N-m. Determine: (a) the maximum shear stress T₂ in tube segment (2). (b) the angle of twist 2 in tube segment (2). (c) the rotation angle DIA of gear D relative to gear A. T Answers: (a) T₂ = (b) ₂ = (c) & DIA (1) = B i i L2 (2) MPa. C L3 (3) T D X
Which set of compatibility equations matches the following torsion members connected end-to-end in series? 30 in. O || = C a 560 8₁ a & + gap 05/0 18 in. 6 in. (2) 0 & + ₂ = 0 О ф, = фг 0 8₁ = 8₂ - 8₂ 04+₂=0 & + ₂ = constant Ta (3) 8₁ + gap = 8₂ &₁ = & + gap D. & + ₂ = constant 8 in. (2)
Consider the compound shaft KC which is composed of a 1200mm long solid rod fitted snuggly into an equally long pipe. Refer to the figure for given dimensions and material properties. If end K is fixed to a rigid wall and a concentrated torque is applied at end C, determine the following: Pipe E 115 GPa G = 36.0 GPa 48.0 MPa Ty 1200 mm ø180mm Rod E = 220 GPa G 85.0 GPa 80.0 MPa 1. The required outer diameter for the pipe such that the rod and the pipe yields simultaneously. 2. The corresponding maximum angle of twist of the shaft when it yields. 3. The corresponding maximum torque T that can be applied at end C of the shaft
Consider the compound shaft KC which is composed of a 1200mm long solid rod fitted snuggly into an equally long pipe. Refer to the figure for given dimensions and material properties. If end K is fixed to a rigid wall and a concentrated torque is applied at end C, determine the following: Pipe E = 115 GPa G - 36.0 GPa 1, = 48.0 MPa 1200 mm 180mm Rod E = 220 GPa G = 85.0 GPa *, 80.0 MPa 1. The required outer diameter for the pipe such that the rod and the pipe yields simultaneously. 2. The corresponding maximum angle of twist of the shaft when it yields. 3. The corresponding maximum torque T that can be applied at end C of the shaft
Question 4 fixed. The shear modulus G and the polar moment of inertia I, of the bar's cross-section are constant along the bar's axis. From the fixed left end (x = 0) of the bar to the middle (x = L/2) of the bar, a lincarly varying distributed torque t, = kr, 0 < x < L/2 is applied (the unit of t, is N-m/m). At the free end (r = L) of the bar, a concentrated torque T is applied (the unit of T is N-m). According to the right-hand rule, the linearly varying distributed torque t, and the concentrated torque T both point to the r-positive direction. Find the angle of twist at the free end (x = L) (Expressing the result with G, Ip, L, T, and k). (Hint: It is easier to find the angle of twist using & = f Figure 1 shows a bar under torsion. The left end of the bar is E.) t, = kx L/2 L/2 Fig. 1. The left end (r = 0) of the bar is fixed, and the right end (r = L) of the bar is applied with a concentrated torque T. A linearly varying distributed torque t, is applied from the left end (z = 0) of…
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M
Form the figure below, the power transmission shaft shows the forces acting on it carrying two gears. The gears are keyed at B and D. A and C are journal bearing centers. Ten hp is transmitted at 750 rpm of the shaft. Assume allowable stress for an unkeyed section equal to 12,000 psi and use Km=K¡ = 2.0. What is the approximate shaft diameter in inches? 4 in 8 in 3 in 320.15 450 lb 105 !b sis lb Do not include the units in encoding the answer. Two decimal places only.
A compound steel shaft consists of solid 21-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 42 mm and a wall thickness of 2.3 mm. Assume T = 350 N·m, L1 = 1.4 m, L2 = 1.5 m, and L3 = 1.4 m. Calculate the polar moment of inertia for tube segment (2). Determine the maximum shear stress in tube segment (2).
The torsional assembly consists of solid 1.6 in. diameter aluminum [G = 4,000 ksi] segments (1) and (3) and a central solid 2.0 in. diameter bronze [G = 6,500 ksi] segment (2). Segment lengths are L1 = L3 = 32 in. and L2 = 66 in. Concentrated torques of TB = 2T0 and TC = T0 are applied to the assembly at B and C, respectively. If the rotation angle at joint B must not exceed 3.0°, determine:(a) the maximum magnitude of T0 that may be applied to the assembly.(b) the maximum shear stress magnitude in aluminum segments (1) and (3).(c) the maximum shear stress magnitude in bronze segment (2).