An aluminum cup of 150 cm³ capacity is completely filled with glycerin at 16°C. How much glycerin will spill out of the cup if the temperature of both the cup and glycerin is increased to 39°C? (The linear expansion coefficient of aluminum is 23 x 106 1/C°. TH coefficient of volume expansion of glycerin is 5.1 × 10-4 1/Cº) loth prob Units Number

An aluminum cup of 150 cm³ capacity is completely filled with glycerin at 16°C. How much glycerin will spill out of the cup if the temperature of both the cup and glycerin is increased to 39°C? (The linear expansion coefficient of aluminum is 23 x 106 1/C°. TH coefficient of volume expansion of glycerin is 5.1 × 10-4 1/Cº) loth prob Units Number

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter4: Temperature Effects On Atom Arrangements And Atom Motion

Section: Chapter Questions

Problem 4.5P

See similar textbooks

Similar questions

An aluminum calorimeter with a mass of 100 g contains 250 g of water. The calorimeter and water are in thermal equilibrium at 10.0°C. Two metallic blocks are placed into the water. One is a 50.0-g piece of copper at 80.0°C. The other has a mass of 70.0 g and is originally at a temperature of 100°C. The entire system stabilizes at a final temperature of 20.0°C. (a) Determine the specific heat of the unknown sample?
An aluminum pipe has a length of 60 m at a temperature of 10° C. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aAL=23x 10^-6°C and as=12x10^-6° C respectively)
2. In a copper-nickel system as shown in figure, an alloy composition of 35 wt% Ni was cooled down from the temperature of 1300°C. Sketch the expected microstructures at the point a, b, c, d and e and briefly describe the development of these microstructures in the equilibrium cooling. L. L (35 Ni) 1300 L (32 Ni) a (46 Ni) a(43 Ni) L (24 Ni) d 1200 1100 20 30 40 50 Composition (wt% Ni) Temperature (°C))
A square high-density polyethylene [a = 158 × 10-6/°C] plate has a width of 295 mm. A 177 mm diameter circular hole is located at the center of the plate. If the temperature of the plate increases by 45°C, determine: (a) the change in width of the plate. (b) the change in diameter of the hole. Answer: (a) Aw= (b) Ad = i i mm mm
An aluminum pipe has a length of 53 m at a temperature of 7°C. An adjacent steel pipe at the same temperature is 7 mm longer. At what temperature will the aluminum pipe be 21 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5x10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×106/°C. Answer: Tf = i °C
What temperature is required to obtain 0.4%C at a distance of 0.3 mm beneath the surface of a 0.22% C steel in 2h, when 1.1% C is present at the surface? Assume that the iron is FCC. (Please see figure 5.12 below for diffusion coefficient data. Please use your notes for a table of erf() function values Diffusion coefficient D (cm²/s) ܐ ܐ ܐ ܐ 10- 10-5 10- 10-10 10-11 10-12 10-13 10-14 10-15 Temperature (°C) 2000 1500 1200 1000 900 800 700 600 Cin graphite Mg in MgO Ca in Cao H in FCC iron C in FCC iron Fe in FCC iron Fe in BCC iron H in BCC iron C in BCC iron Fe in FeO 500 5 6 7 8 9 10 11 12 13 104 T(K) Figure 5-12 The diffusion coefficient D as a function of reciprocal temperature for some metals and ceramics. In this Arrhenius plot, D represents the rate of the diffusion process. A steep slope denotes a high activation energy.
An aluminum pipe has a length of 65 m at a temperature of 16°C. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. At what temperature (in degrees Celsius) will the aluminum pipe be 14 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are a, = 23 x 10-6/°C and a = 12 x 10-6/°C, respectively. Also assume that the temperature of both pipes change equally.) °C
An aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. (a) At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are ca=23x10-6/°C and as=12x10-6/°C, respectively.) (b) What is the axial stress developed in the aluminum pipe when the temperature was increased? Aluminun Steel Figure No. 1 5 mm
-A rod 3 m long is heated from (10 to 90) °C, if the modulus of elasticity equal to 10000O MN/m2, and coefficient of thermal expansion = 0.000012 per °C, the new long of rod after expansion is 0.168 cm 0.288 cm 0.208 cm 0.348 cm 0.388 cm Other:
The aluminum tube AB of cross section has a fixed support on the base and is supported by a pin at the top of a horizontal beam supporting a load Q = 200 kN. Determine the required thickness t of the tube if its outside diameter for 100 mm and the necessary safety factor in relation to Euler buckling for n = 3.0 (assuming A = 72 GPa). I know the answer, but I cannot understand the critical charge formula. I don't know why to use the constant 2.046 in the formula, can you please show me?
An aluminum pipe has a length of 69 m at a temperature of 8°C. An adjacent steel pipe at the same temperature is 5 mm longer. At what temperature will the aluminum pipe be 15 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5×10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×10-6/°C.
1) A phosphor-bronze spring has the following dimensions: Length of strip = 400 mm Thickness of strip = 0.075 mm Width of strip = 0.5 mm The Young's modulus of phosphor-bronze is 12× 109 kg/m2. Estimate the torque exerted by the spring when it is turned through 90°. %3D [Ans. 0.83 x 10–6 kgm]