An aluminum alloy pipe with an outside diameter of 4.9 in. and a wall thickness of 2/16 in. cantilevers upward a distance of L-21 ft. The pipe is subjected to a wind loading that increases from WA-12 lb/ft at its base to wg = 18 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?

An aluminum alloy pipe with an outside diameter of 4.9 in. and a wall thickness of 2/16 in. cantilevers upward a distance of L-21 ft. The pipe is subjected to a wind loading that increases from WA-12 lb/ft at its base to wg = 18 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Can someone please answer this? Thank you, in advance.
3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A. 300 kN A V 300 kN
The elliptical pipe carrying steam at 3.5 mPa has an outer major axis length of 500 mm and an outer minor axis length of 400 mm with a wall thickness of 10 mm. A gasket is inserted between the flange at end of the pipe , and a flat plate is attached using 40 mm diameter bolts to cap the end . The allowable Stress in the bolts is 80 Mpa. How many bolts must be used to hold the cap if there is an initial stress of 30 mPa ?
Determine normal stresses at A and B. Are these point of maximum and minimum normal stresses? If not where are they located and what their values.
5. A 30 cm radius Cast iron main leads from a reservoir whose water surface is at EL. 1590m. In the heart of the city the main, below ground level, is at EL. 1410m. (a) What is the net pressure (b) Assuming static conditions, what is the stress in the pipe wall if the wall thickness is 12.00 mm and the external soil pressure is 250 kPa?6. A continuous wood stave pipe is 2.5 m in diameter and is in service under a head of 30.0 m of water. The staves are secure by means of round 25 mm steel hoops with an allowable stress of 105 MPa. Fine the maximum snarings of the hoops to safely secure the nine.
A 2024-T4 aluminum tube with an outside diameter of 2.4 in. will be used to support a 30-kip load. If the axial stress in the member must be limited to 17.5 ksi, determine the wall thickness required for the tube.
Q1 : For a yield strength of 50 kpsi find the factor of safety at point A using the maximum shear stress theory. [Ans 2.34] 1.25 in.- 60 in.- 200 Ib 200 Ib -24 in.- 24 in.- 1.5 in. Web and flange thickness 0.125 in
An aluminum alloy pipe with an outside diameter of 4.3 in. and a wall thickness of 5/16 in. cantilevers upward a distance of L = 22 ft. The pipe is subjected to a wind loading that increases from wA = 8 lb/ft at its base to wB = 12 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
The sign post shown has an outside diameter of 12-in. and a wall thickness of 0.50-in. Determine the maximum load P that can be applied while limiting the maximum tensile stress at the base to < 36 ksi. 1.5P P 10 ft 7 ft C 20 ft D.
An aluminum alloy pipe with an outside diameter of 4.0 in. and a wall thickness of 6/16 in. cantilevers upward a distance of L = 12 ft. The pipe is subjected to a wind loading that increases from wA = 11 lb/ft at its base to wB = 17 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
At the proportional limit, the axial bad of a 0.90-in-diameter bar was 5800 1b, A 2.40 in, gauge length on the bar has increased by 0.0048 inch,