An all welded vertical cylindrical tank 24m in diameter by 15m high is designed for storage of molasses(SG=1.5).Determine the minimum thickness of the shell plate if the allowable stress of the plate is 140MPA and the welding efficiency was 80%. Allow 1.6m free board for air space in the tank. Round off your answer to whole number.

An all welded vertical cylindrical tank 24m in diameter by 15m high is designed for storage of molasses(SG=1.5).Determine the minimum thickness of the shell plate if the allowable stress of the plate is 140MPA and the welding efficiency was 80%. Allow 1.6m free board for air space in the tank. Round off your answer to whole number.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

600mm 100mm 50mm x 50mm hole 500mm 10mm A 100mm Figure 3 Show that the horizontal neutral axis is 77.56mm below B. Hence, show that the moment of inertia around this horizontal neutral axis is 3178942345mm4. Show the division of your area on a sketch on your answer sheet. a) (use the answers in (a) for (b), (c), (d) and (e)) b) Draw the 3D normal stress distribution of the section subjected to M = -10 kN.m. Draw the shear stress distribution of the section if the section is subjected to a shear force of 10KN. c) d) What part of the shear force is carried by the flange? e) What part of the bending moment is carried by the flange
Multiple Attempts Not allowed. This test can only be taken once. Force Completion This test can be saved and resumed later. This test does not allow backtracking. Changes to the answer after submission are prohi Your answers are saved automatically. A Question Completion Status: 1 3 4 5 7 A Moving to the next question prevents changes to this answer. Question 1 Compute the moment of inertia about the centroidal x-axis Dimensions in inches 7.5 3. 3 6. ASUS ZenBook
Let L be the line with parametric equationsx = 1−ty = −4z = 4+tFind the shortest distance d from the point P0=(4, −1, −1) to L, and the point Q on L that is closest to P0. Use the square root symbol '√' where needed to give an exact value for your answer.
Using Virtual Work Method Find the smallest value of P acting at the FD midspan that is required in order to get a zero deflection at point B. For two steel beams EI = 400,000 kNm² Please box your final answers I'll thumbs up on the correct answer. please see the note, below before answering. Final answers in the solution sheet should be rounded to three (3) decimal places and should be enclosed in a rectangle for easy identification. Final answers for locations or distances must be given in meters or feet. Final responses for deflections must be given in millimeters or inches. NOTE: No final solutions shall be in scientific notation. Final answers for slopes shall be in degrees to 5 decimal places.
II. Problem Solving. Provide a complete and orderly solution to the given problem and submit your answers in pdf format. A section of a reinforced concrete elevator shaft is shown in the figure. Compute the following: a. Centroid of section; b. Centroidal Moments of Inertia; and c. Rigidity about the centroidal axes. Consider the effect of shear deflection. Assume h = 15m, P = 1000 kN, and f'c = 24 MPa. C 0.40 2.83 Note: Elevator shaft dimensions are in meters. 3.24 1.12 1.12
1. Given: A structure shown below Find: (1) Determine the magnitudes and locations of the two distributed loadings. In other words, determine the magnitude and location of the loading between A and C, and those of the loading between D and B. (2) For the member DEB, (a) take the moment at B and find the reaction at E and (b) then find By by either Fy= 0, or EMp = 0. (Recall that support conditions at B and E are rollers, so there are no reactions in x-direction.) (3) For the whole structure, 3 unknown forces and moment at A (Ax, Ay and Ma) are the only unknowns. Determine those 3 unknowns at A. 900 N/m 900 N/m B A C D 2E - 3 m 3 m - 4 m - 3 m3 m-
On a three-dimensional cartesian plane, Points A, B, C, and D are to be plotted as follows: POINT: A: B: C: D: Determine the x-component of vector AB. Express your answer in terms of the units on the DROP-DOWN MENU (if applicable). Observe 3 decimal places. The error threshold is t 2.50 % Relative to the right answer. DO NOT INDICATE UNITS ON THE ANSWER BOX Answer: Determine the y-component of vector AB. Express your answer in terms of the units on the DROP-DOWN MENU (if applicable) Observe 3 decimal places. The error threshold is t 2.50 % Relative to the right answer. DO NOT INDICATE UNITS ON THE ANSWER BOX Answer:
The solutions and answers should have minimum of 3 decimals for linear measurements and should be in Degree-Minute-Seconds (2 decimals for seconds) for angular measurement, if not whole number. An engineer is tasked to measure a whole line multiple time. Since the length of the line is significantly longer than the steel tape, the engineer decided to measure the line in three segments. First, the engineer measures a 50m known line using the steel tape and find out that the tape is too long with the observation having only 49.2m. With these values, the correction factor of ???? = 50? − 49.2?. After determining such corrections for future calibration, the engineer measured each segments. The following are the observations: 1st Segment: 46.2m, 46.3m, 46.5m; 2nd Segment: 48.3m, 48.2m, 48.1m; 3rd Segment: 32.3m, 32.6m, 32.4m. Determine the complete expression of the most probable value (together with probable error) of the line.
Clean handwriting answer it okkk must handwriting thanks. Don't use chat gpt answers okk I use chat gpt there all answers wrong .pre calculus
please answer in a complete solution, thank you!
Using CONJUGATE BEAM METHOD, find the ff. when E=80 GPa and I= 100x10^6 mm^4 a) Location and magnitude of maximum deflection b) Rotation at right support in degrees c) Rotation at left support in degrees *Use metric system only. *Final answers should be rounded off to 3 decimal places and must be boxed.
NEED ASAP PLEASE THANK YOU! NOTE: PLEASE DO NOT ROUND OFF IN BETWEEN SOLUTIONS! AND FINAL ANSWERS IN THREE DECIMAL PLACES.