Answered: An air standard Otto cycle with…

An air standard Otto cycle with compression ratio of 6 , ambient temperature 27°C and temperature after heat addition is 1569°C. Claculate the temperature after isentropic expansion .

Related questions

Q: Shown below is the PV-diagram for a clockwise cycle. Determine the work done during the cycle, the…

A: Given that the system's is in circular motion so dw=0 and work are both equal to zero. U therefore…

Q: In the shown Figure, the network done by the gas during the close cycle is equal to: P (P₂) 6x104…

Q: Question 4) A cylinder with a piston contains 2 mol of Helium gas at 5 x 105 Pa and 500°C. The gas…

Q: Calculate work made by 1.75 moles of ideal gas in the isothermal cycle shown in P-V diagram below.…

Q: Five moles of Nitrogen (behaving like an ideal gas) are taken around cycle acb as shown. Process ac…

Q: One mole of an ideal gas with a temperature of 300 K is expanded by an adiabatic process at a…

Q: A Carnot refrigerator operates between 6500 K and 550 K. It extracts 890 J from a cold reservoir…

Q: Suppose a Carnot refrigerator operates between Tc and Th. Calculate the amount of work required to…

A: Given Amount of heat rejected to cold reservoir Qc = 1.0 J

Q: As shown in the figure, a chamber with a moveable piston and containing a monatomic ideal gas in an…

Q: 49. . A Carnot engine with an efficiency of 40% oper- ates with a low-temperature reservoir at 40 °C…

Q: Calculate the entropy change in kJ/K, of 10kg of Silver when it’s temperature increases from 20…

Q: Five liters of air initially at 600K and 500 kPa is used in a Carnot engine and expanded to 10…

Q: As shown in the figure, a chamber with a moveable piston and containing a monatomic ideal gas in an…

Q: An air-standard Diesel cycle has a compression ratio of 16 and a cut-off ratio of 3. The state at…

A: Hint: Ideal gas equation pVk = constant; TVk-1 = constant Compression ratio r = V1V2 Thermal…

Q: 48 Go As a gas is held within a closed chamber, it passes through the cycle shown in Fig. 18-41.…

Q: The following processes occurs in a reversible thermodynamic cycle: 1-2: Reversible polytropic…

A: Given,For process1-2:P1 = 0.8 barV1 = 0.05m3P2 = 10.1 barV2m = specific volume = 0.4 m3Kgindex of…

Q: 2. Calculate the maximum work that can be done by a reversible heat engine operating between 500 and…

Q: Ques 2 po (CLO-6J Superheated water vapor enters an irreversible adiabatic turbine at 5 MPa and 500…

Q: 2Po - B P. P.

A: Number of moles, n=1 paths AB and CB are isothermal, paths BC and DA are isobaric. at all the points…

Q: A gas within a piston-cylinder assembly executes a Carnot power cycle during which the isothermal…

A: a)The equation for the efficiency of a Carnot engine is given by,

Q: Which of the two gases—helium or nitrogen—experiences the greatest entropy change as its state is…

A: The given values are, From the properties of the helium and the nitrogen,

Q: Question 3) A cylinder with a piston contains 0.25 mol of 02 (treat as ideal gas) at 2.40 x 105 Pa…

A: Given : n = 0.25 mol ( of O2) ; T1 = 355 K; Pressure (P1) = 2.40 x 105 Pa

Q: One mole of a monoatomic, ideal gas goes through the cycle shown in the diagram. Paths AB and CD are…

Q: 50g of water at 60oC is transferred to a pan and evaporated to dryness at 100oC at constant…

A: Convert the temperature of the water from degree Celsius to Kelvin. And,

Q: Air enters the compressor of an ideal cold air-standard Brayton cycle at 1 bar, 27 °C, with a mass…

A: To calculate the back work ratio in the Brayton cycle, we need to determine the specific enthalpy…

Q: (b) Patm) 20 Figure 3 1.5 0.3 Vliters) In Figure 3, given that one mole of gas is initially ata…

A: Given data: Initial conditions, P1=2 atmV1=0.3 LU1=91 J Final conditions, P2=1.5 atmV2=0.8 LU2=182 J

Q: Superheated steam at 18 MPa, 560 degree Celsius, enters the turbine of a vapor power plant. The…

A: Given:Turbine inlet pressure, p1=18MPaTurbine inlet temperature, T1=560CoTurbine exit pressure,…

Q: The following process occurs in a reversible thermodynamic cycle : 1-2 : Reversible polytropic…

A: According to our guidelines We’ll answer the first subparts of the question since the exact one…

Q: otion and the brake mean I charge is 1.05 kg/m3 ar

A: Given: To find the brake specific fuel and mean effective pressure is given as,

Q: An ideal Diesel cycle has a compression ratio of 17 and a cutoff ratio of 1.3. Determine the maximum…

Q: The pressure and temperature at the beginning of compression of a cold air-standard Diesel cycle are…

A: Note: As per the guidelines, we can only answer three subparts of a question. Sorry for the…

Q: For the given cyclic process CAB as shown for a gas, the work done is A 6.0 5+ 4+ p (Pa) 3+ 2+ 1. 4…

Q: Calculate ΔA for the isothermal compression of 1.54 mol of an ideal gas at 322 K from an initial…

Q: A gas-turbine power plant operates on the simple Brayton cycle with air as the working fluid and…

Q: The compression ratio of an air-standard Otto cycle is 9.5. Prior to the isentropic compression…

Q: What is Carnot efficiency of a heat engine operating between the temperatures of 381 Co and -11 Co…

A: Carnot efficiency of a heat engine operating between the temperatures of T1 and T2 is given by,…

Q: One mole of an ideal gas is heated at constant pressure so that its temperature increases by a…

A: Workdone in an isobaric process (pressure constant) is given by, Wisobaric =…

Question

An air standard Otto cycle with compression ratio of 6 , ambient temperature 27°C and temperature after heat addition is 1569°C. Claculate the temperature after isentropic expansion .

Expert Solution