An air lossless transmission line is operating at frequency of 4 MHz and has a length of 0.25 ), characteristic impedance of 75 Q and terminated by a load of 125 What is the wavelength on the transmission line in meters? What is the load reflection coefficient ? What is the input impedance of the TL? What is the maximum input impedance that can be encountered on this TL? If the maximum voltage on the TL is |V]max = 25 V, what is the minimum current Unin ?

An air lossless transmission line is operating at frequency of 4 MHz and has a length of 0.25 ), characteristic impedance of 75 Q and terminated by a load of 125 What is the wavelength on the transmission line in meters? What is the load reflection coefficient ? What is the input impedance of the TL? What is the maximum input impedance that can be encountered on this TL? If the maximum voltage on the TL is |V]max = 25 V, what is the minimum current Unin ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.8P

See similar textbooks

Similar questions

A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight 1-The capacitance in uF/km without effect of ground is 2-The capacitance in pF/km with effect of ground is
7- DC Chopper with output voltage of 120V and input voltage of 80V and output power of 240W. Assume lossless chopper. The average inductance current IL is * 2.6 A 3.0A 4.3A 8- taking into account obtained duty cycle from previous task, the needed : capacitor for realizing 1% ripples at frequency of 10kHz is? * ?? 55.56 uF O 13. 34 uF 92.44 uF
The open circuit imepdance of a certain length of a loss-less line is 100 ohm. The short circuit impedance of the same line is also 100 ohm. What wilp be its characteristic impedance ?
8. A transmission line has a characteristic impedance of 500 and a resistance of 0.1 02/m. If the line is distortion less, the attenuation constant (in Np/m) is (a) 500 (b) 5 (c) 0.014 (d) 0.002
A lossless TL with if the voltage a cross a load connected to lossless TL is 20 Vyms and reflection coefficient is equal to KR = 0.7470°. 1. Find VSWR (S) for this TL. 2. Find the voltage and current scales. 3. Find the voltage and current at d= 0, 1/8, 2/4, 32/8 and 2/2 using Crank diagram and tabulate the results, including the distances and the values for maximum and minimum voltage, current, i.e. Emax and Emin at dmax and dmin, respectively. 4. From Crank diagram confirm that S has the same value found theoretically already in (1) above. 5. Use Crank diagram to evaluate the transmitted power. 6. Draw clearly the SWR pattern from d= 0 to d=12 showing the maximum and minimum positions in your plot. 7. If the load is changed to ZR= Z0 how would the SWR pattern look like? Why? Draw it clearly.
A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight meter. Determine 1)The capacitance in uF/km without effect of ground 2)The capacitance in uF/km with effect of ground
c) For a transmission line w/characteristic impedance Z0 = 50 W. At some point of the line, a forward wave has the voltage V+ = 10V and backward wave has the voltage V- = 4V. i) Currents of the forward wave and backward wave at that point. ii) Measured voltage and current at that point. d) A transmission line has the following properties: Length, L = 3 m. Characteristic impedance Z0 = 50 W. The load impedance ZL = 100 W. And phase constant b = p/3. Assume the forward voltage at z = 0 is VA =10ejp/4 At z = 3m, calculate: i) Forward voltage and forward current. ii) Backward voltage and backward current. iii) Measured (total) voltage and current across the load
A lossless TL with if the voltage a cross a load connected to lossless TL is 20 V,ms and reflection coefficient is equal to KR = 0.7470°. 1. Find VSWR (S) for this TL. 2. Find the voltage and current scales. 3. Find the voltage and current at d= 0, 1/8, 2/4, 31/8 and /2 using Crank diagram and tabulate the results, including the distances and the values for maximum and minimum voltage, current, i.e. Emax and Emin at dmax and dmin, respectively. 4. From Crank diagram confirm that S has the same value found theoretically already in (1) above. 5. Use Crank diagram to evaluate the transmitted power. 6. Draw clearly the SWR pattern from d 0 to d=12 showing the maximum and minimum positions in your plot. 7. If the load is changed to Ze Z0 how would the SWR pattern look like? Why? Draw it clearly.
The capacitance per unit length and the characteristic impedance of a lossless transmission line are C and Zo respectively. The velocity of a travelling wave on the transmission line is (a) Z.C (c) Zo C - UN (b) Z.C (d) Z
The characteristic impedance of a lossless line is 50 ohm and the length of the line is half wavelength. The impedance of the load connected to the end of the line is 75 Ohm. Find the impedance visible from the beginning of the line. A) 50ohm B) -j*25 ohm C) 25 ohm D) j*50ohm E) 75 ohm
9. Calculate the return loss in dB if the voltage load reflection coefficient is 0.24. None of them 0.124 dB 124 dB 12.4 dB 1.24 dB 10. A piece of quarter wavelength transmission line is inserted between a load 1000brand another transmission line of 70-50 Then the characteristic
Answer briefly (12) of the following questions: 1) In a lossy transmission line, what is the formula of the propagation constant (y) of the transmission line? 2) When the transmission line is terminated by an open circuit, what is the value of the reflection coefficient (TL) and VSWR? 3) When the transmission line is terminated by a matched load, what is the value of the VSWR? 4) Find the characteristic impedance of the Quarter wave transformer to match 75 2 load impedance with a 50 2 transmission line. 5) If a transmission line has a characteristic impedance of 47+ j52 2. What is the value of the load that must be connected to transfer maximum power? 6) If the amplitude of the carrier signal is 7V, and the modulation index m=0.8, find the amplitude of the message signal? 7) Over modulation occurs when signal amplitude is carrier amplitude. (equal, greater than, less than) 8) If the highest frequency of the baseband signal is 6 kHz, what is bandwidth of the DSBAM and SSB signal? 9) In…