An action will release DO and BOD to a large low velocity river at a location where the existing conditions of the river have already been determined. Assess the impacted conditions (as a result of this action) at a location 10,000 m down-river from where the action releases the pollution. River: Q = 2 m³/s, A=1m², T = 15 degC, L = 5 mg/L, DO = DOsat Source1: Q = 0.5 m³/s, T = 25 degC, L = 100 mg/L, DO = = 1 mg/L

An action will release DO and BOD to a large low velocity river at a location where the existing conditions of the river have already been determined. Assess the impacted conditions (as a result of this action) at a location 10,000 m down-river from where the action releases the pollution. River: Q = 2 m³/s, A=1m², T = 15 degC, L = 5 mg/L, DO = DOsat Source1: Q = 0.5 m³/s, T = 25 degC, L = 100 mg/L, DO = = 1 mg/L

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.6P

See similar textbooks

Similar questions

1) A production well was discharged and tested through an atmospheric silencer at sea level (1 barabsolute) using a lip pipe with a diameter of 25 cm and a weir box with a 90 ° V-notch weir. The well wasflowing at a wellhead pressure of 6.5 bar gauge and the measured lip pipe pressure and weir heightwere 3 bar gauge and 0.10 m, respectively. Calculate the discharge enthalpy and total mass flow of thewell. 2) answer A B AND C on the pic
5) Two reservoirs have a minimum difference in water-surface elevation of 40 m and are connected by a 5000 m long, 0.2 m diameter pipe of roughness 0.03 mm. The entrance and exit loss coefficients are 0.8 and 1.0, respectively. a) Determine the minimum discharge in the pipe for this condition. b) It is desired to increase the discharge to 0.05 m3/s by using an equivalent diameter pipe with a roughness of 0.015 mm placed in parallel to the existing pipe. Determine the length of this second pipe. Ignore minor losses. 40'
Discuss the options available in selecting flow conduits for the production of the two reservoirs and explain the factors that influence flow conduits selection. Mention 2 advantage and disadvantage of of the these available options in your duscussion.
(2) An aquifer of area extent 100 km / sq is overlain by & Strata as gives below: Strata 1 (top) 2 3 4 thickness 1 3 2 4 Ka (m/day) Ky(m/day) 0-25 0.3 1 2 1-5 0.025 205 0.2 0-005 estimate the (a) If a 4 hour storm occurs producing a total rainfall of 100 mm recharge into the aquifer assuming the piezometric Surface in the aquifer is at the bottom layer of and all layers are saturated (b) If the 4 layers. are underlain by an impermeable strata instead estimate the lateral flow per unit weight through the layers assuming. layer is deep by 0.1%. of aquifer that the
Plz, solve all the parts of this problem. Use Excel sheet. Reg.No: 5395 Hydraulics A rectangular channel carrying 30 cfs has a bottom width of 4 ft. Manning roughness coefficient is 0.0a, where a = last digit of your registration number. Assume ten different depths of the flow and DEVELOP a specific energy diagram, using Excel sheet, for the given flow in this channel. Show (CLO3) 1) All the alternate depths and the corresponding energies. 2) The critical flow parameters. 3) Relationship between specific energy and the depth of flow for no velocity in a given channel
(b) Explain three common purposes of reservoirs in arid countries.
The following data obtained from depleted oil reservoir: A= 10 acres, h-20 ft, PHI=22%, Soi-0.65. Sor-0.30, Bo-1.31 RBSTB, Kro-0.8, Krw-0.24. iw-100 RB/day, the reservoir is subjected to water flooding, calculate the recovered oil volume and time of breakthrough if E-55%. If the flooding continue and a one and half pore volume of water are injected calculate recovered oil volume and the time of recovery knowing that E= 90 %.
The dam and flow net shown in the attached picture. The dam is 120 m long and has two 10 m sheet piles driven partially into the granular soil layer. Datum is at tailwater elevation. Determine: 1. The quantity of seepage loss under the dam when k= 20*10^(-4) cm/s 12 m 10 m sheet pile 10m sheet pille 85m 30 m Impervious - O C 0.4 1 Scale: Number al equipotential drops
Question 7 (Parallel pipes) Two reservoirs are connected by two parallel pipelines with diameters of 0.8m and 0.6m as shown in Figure 8. The pipelines are both 3 km long with a value of 0.03. The combine discharge through the pipelines must be at least. Pipe 2 Pipe 1 Figure 8 a) When the total discharge is, what is the flow rate in the individual pipeline? b) What is the minimum difference in the elevation of the surface water level in the two reservoirs required to maintain a flow of through the pipelines?
A tannery with a wastewater flow of 0.011 m3/s and a BOD5 of 590 mg/Ldischarges into the Cattaraugus Creek (Nemerow, 1974). The creek has a10-year, 7-day low flow of 1.7 m3/s. Upstream of the tannery, the BOD5of the creek is 0.6 mg/L. The BOD rate constants k are 0.115 d21 for thetannery and 3.7 d21 for the creek. The temperature of both the creek andthe tannery wastewater is 208C. Calculate the initial ultimate BOD aftermixing.
two sedimentation tanks operate in parallel. The combined flow to the two tanks is .1 m^3/s. the depth of each tank is 2 m and each has a detention time of 4 h. what is the surface area of each tank and what is the overflow rate of each tank in m^3/d*m^2? Please don't provide handwritten solution
A water treatment plant operates two circular sedimentation basins in parallel to remove suspended solids and treats a total flow of 12 mgd. Each basin is center-fed (i.e., water comes into the reactor in the middle and radiates toward the outside of the basin) and the solid-free water exits the reactor over weirs that are located 2 feet within the basin perimeter. Each tank has a diameter of 65 feet with a water depth of 12 feet. 2. What is the detention time in each clarifier (in minutes)? b. What is the overflow rate for each clarifier (in ft/ft?-d and gpd/ft?)? What is the weir loading rate for each clarifier (in ft'/ft-d and gpd/ft)? d. Calculate the values for parts a-c if only one clarifier is in service.