▪ An ac amplifier has a midband voltage gain of 200. If the cutoff frequencies are fl= 20 Hz and f2 = 20 kHz, what does the frequency response look like? What is the voltage gain if the input frequency is 5 Hz? If it is 200 kHz? ▪ A 741C op-amp has a midband voltage gain of 100,000. If f2 =10 Hz, what does the frequency response look like? What is the voltage gain for each of the following input frequencies: 100 Hz, 1 kHz, 10 kHz, 100 kHz, and 1 MHz?

▪ An ac amplifier has a midband voltage gain of 200. If the cutoff frequencies are fl= 20 Hz and f2 = 20 kHz, what does the frequency response look like? What is the voltage gain if the input frequency is 5 Hz? If it is 200 kHz? ▪ A 741C op-amp has a midband voltage gain of 100,000. If f2 =10 Hz, what does the frequency response look like? What is the voltage gain for each of the following input frequencies: 100 Hz, 1 kHz, 10 kHz, 100 kHz, and 1 MHz?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Construct the small signal model of the circuit shown below:
In an inverting op-amp, has the following. Rf=20K, R1=5K and Vin=3 volts. What is the gain of this Amplifier?
slove 5 (Use a BJT op-amp) 1 You’ve been asked to build an alarm system using monstable multvibrator having an active time pf 100msec.. Explain the principle of operation and the type feedback of the op-amp. What is the advantage of this circuit? 2 You’ve been asked to build a low frequency square wave generator using a basic comparator having a frequency of 10kHz and 50% duty cycle. Explain the principle of operation and the type of feedback of the op-amp. What is the advantage of this circuit? 3 3 Build a Wein-Bridge oscillator using, C=1µF and +10V power supply to produce 10 kHz sinusoidal waveform. Generate your plots and compare output results. Highlight any discrepancies and discuss what happens if we want to increase the frequency to 100 kHz. 4 Build a high frequency Colpitts oscillator producing 10kHz Discuss its advantage over RC oscillators. How can you modify the circuit to include a crystal in you circuit. What is a typical application of such an oscillator? 5 Discuss the…
6. For common-source small-signal FETS, the output voltage is 180° phase shifted with respect to the Q 7. The operating cycle of a Class A amplifier is Q 8. The maximum efficiency of a Class B amplifier is Q 9. In analyzing op-amps, when the non-inverting input pin is at ground and the inverting input pin is also at 0 V for an AC signal, the technique is called as Q 10. is an op-amp application circuit which is useful in low pass filter circuits.
Class B Amplifier q1)If the input is 7.5Vp-p...DATA COLLECTION: What is the IL(peak)? a)7mA 6)mA 5)mA 4)mA q2) DATA COLLECTION: What is the Idc? a)3.84 b)4.82 c)3.82mA d)1.82mA q3)DATA COLLECTION: What is the input power in DC? Power input = 48.45mW Power input = 45.48mW Power input = 44.58mW Power input = 45.84mW q4) DATA COLLECTION: What is the output power in AC? a)18mW b)81mW c)11.8mW d)18.9mW q5)DATA COLLECTION: What is the power dissapated by each transistor? a)35.1mW b)53.1mW c)15.3mW d)13.5mW q6)DATA COLLECTION: What is the efficiency of class B amplifier? a)45% b)40% c)63% d)33% q7)
List the elements included in the total input resistance of a common-collector amplifier. What is the phase relationship of the input and output voltages of a CE(common emitter) and CC(common collector) amplifier? 0 T-fo TE
3G Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. Determine the output voltage of the second stage stage. a.-2640 mV b.-26.4 mV c.-1.2 mV d.26 V
These questions from electronics lab course, from The common Collector Amplifier (Emitter-Follower) Experiment.
3A Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. 3H Determine the total gain of the circuit in Problem No. 1 (P1) a.792.105 b.9000 c.792 V d.792
3ZD Calculate the output voltage of an op-amp if a 100mV signal is applied to the non-inverting input of the op-amp circuit which has an Rf = 0 Ohms and Ri = 0 Ohms. a.Infinity Volts b.0 Volts c.1 Volts d.-2 Volts
(a) An instrumentation system shown in Figure Q3 (a-i) has a Nickel resistor detector device (RTD) sensor with the characteristics shown Figure Q3 (a-ii). The three wires bridge has R1= 200 Q, R2= 500 Q, and R3= 650 Q. The amplifier has a gain of 17.2, and the battery voltage is VB=1.2v. (i) Calculate the amplifier output voltage Vo when the boiler temperature is 150 °C. (ii) Explain the RTD principle of operation. R1 R2 Industrial boiler Nickel R3 RTD Vaa Vo Figure Q3 (a-i) 400 Nickel 350 300 Platinum 250 200 150 100 50 Copper -200 200 400 600 800 RTD temperature (oC) Figure Q3 (a-i) RTD Resistance ()