An abc phase sequence three-phase balanced wye-connected source supplies a balanced delta-connected load. The impedance per phase in the delta load is 12.j90. The line voltage at the source is 159.22+j 133.6 V rms. If the line impedance is zero, find the magnitude of the line current in the balanced wye-delta system.

An abc phase sequence three-phase balanced wye-connected source supplies a balanced delta-connected load. The impedance per phase in the delta load is 12.j90. The line voltage at the source is 159.22+j 133.6 V rms. If the line impedance is zero, find the magnitude of the line current in the balanced wye-delta system.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

A balanced delta connected load contains 8 + j4 ohms per phase, while a balanced wye connected loadconsists of 2 – j1 ohms per phase. Both loads are connected in parallel to a three-phase three-wire system inwhich the line voltage is 120 V rms at the loads. The three lines extending from the loads to the source eachhave a resistance of 0.2 ohms. Determine the power lost in the wires.a. 1.42 kW b. 1.38 kW c. 1.24 kW d. 1.83 kW ( please stay on choices, thanks) ..
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the real, reactive, and apparent powers seen at load 1? Give also the power factor.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the RMS line current at load 1 and 2 respectively?
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: Give the value of reactive power per phase seen at load 2.
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
A balanced positive-sequence wye-connected 60-Hz three-phase source has line-to-line voltages of VL = 440 V rms. This source is connected to a balanced wye-connected load. Each phase of the load consists of a 0.5-H inductance in series with a 30-Ω resistance. Assume that the phase of VanVan is zero. FIND Ia,Ib,Ic, Find the power delivered to the load And Find the reactive power delivered to the load.
A 120V (rms), 60Hz three-phase system is supplying power to the following two loads: Load # 1: A balanced load connected in wye with 100ohm resistance and 0.1H inductor connected in series. Load # 2: A balanced load connected in delta with 100ohm resistance and 10uF capacitor connected in series. Draw a circuit diagram and Determine: (i) Total active and reactive power supplied to load # 1 by the system (ii) Total active and reactive power supplied to load # 2 by the system (iii) Magnitude of the total current supplied by the source (iv) Source power factor
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: If the power factor for both loads will be changed to 0.95 lagging using a capacitor parallel to load network, what is the needed reactive power per phase to achieve the required power factor for load 1 and load 2 respectively?
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: If the power factor for both loads will be changed to 0.95 lagging using a capacitor parallel to load network, what is the needed reactive power per phase to achieve the required power factor for load 1 and load 2 respectively? Give also the value of capacitace that must be added to reach the power factor for both load.
A balanced delta connected load has an impedance of (60 +j45) ohm per phase. The load is fed through a line having an impedance of (0.8 +j0.6) ohm per phase. The phase voltage at the terminals of the load is U =480V. The phase sequence is positive.N.B: Use UAB as the reference.a- Calculate the three phase currents of the load.b-Deduce the three line currents I.c- Construct the a-phase equivalent circuit of the system.d- Calculate the three line-to-neutral voltages at the sending end of the line e-deduce the threee to line voltages