Answered: An 8-bit DAC has a reference voltage of…

Engineering

Electrical Engineering

An 8-bit DAC has a reference voltage of 5V. What would be the voltage corresponding to a binary word of 10010011?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Determine the value of Vx and the mode of operation for the PNP transistor shown below. Assume Is =…

A: Vb = 1.2 V VE = VCC = 2 V Betta = 50 VA = infinite RC = 0.1 K ohm VCC = 2V . VX= ?

Q: describe importance laser ablation in combination with ICP-MS in solid sample

A: LA-ICP-MS (Laser Ablation Inductively Coupled Plasma Mass Spectrometry):- It is very sensitive…

Q: A 4:1 transformer is connected to a bridge rectifier circuit with a lkn load. What is the peak…

Q: Addressing mode H.W.1 1. What is the addressing mode of each of the following instructions: a-mov…

A: According to the given question, it is required to determine what type of addressing mode is given…

Q: Sketch the de load line, quiescent collector current, quiescent voltsge, input power, output power…

Q: Parameter Notation Value Voltage at maximum power point Open-circuit voltage Short-circuit current…

Q: What is the differential gain of the differnce stage of the instrumentation apmplifier? What is…

Q: Q. Describe the differences between an analog and a digital value. Give a specific example of an…

A: Analog and digital values are two distinct ways of representing and processing information. The main…

Q: Summary Comparison of BJT, JFET and MOSFET Solid State Devices Disadvantages When Invented…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: Q3: In the adjacent figure, what is the DC load voltage and what is the DC load current? How much…

A: Given, R=1.5ΩTransformer ratio=12:1

Q: What is the fundamental difference between analog and digital circuits, and what are their…

Q: 1-12 Find the voltages V₁ and V₂ in Fig. 1-4d: 1 ≤ + V₁ + V₂ om oo 5kQ ↓ 2mA 10kQ

A: Circuit diagram is given as,

Q: A force sensor was designed using a cantilever load cell and four active strain gauges. (Show that…

Q: A 5-bit flash converter has a reference voltage of 16 V. What is the center code voltage for a…

A: The solution is given below

Q: Q4:-What is the fire angle that required to design an R-triggering circuit for a half wave…

A: In the given question we note that Igt(min) = 0.5mAVgt(min) = 0.7mAVd = 0.7VSupply voltage is…

Q: As a maintenance engineer in a semiconductor company, you are given a task to replace the current…

A: i) ID=41×103=4mAVD=16-1.8KID =16-1.8K×4mA =8.8VVG=1.2K1.2K+3.6K×16 =4VVGS=4-4=0V

Q: PCM is very popular because of the many advantages it offers, enumerate these advantages? What is…

A: Since the full form of PCM is not mentioned so w are considering PCM as Pulse Code Modulation. It is…

Q: Q4-What is the fire angle that required to design an R-triggering circuit for a half wave controlled…

Q: There are two functions of a transistor, that are fundamental to the design of electronic circuits :…

A: Transistor: The transistor is an electronic equipment. It is made through a p and n-type…

Q: 그 Clock D C e D e C B

A: P

Q: In the Drain characteristics of n-channel JFET, if VGS is 0, then the drain current corresponds to…

A: In this question, Choose the correct option In the Drain characteristics of n-channel JFET, if VGS…

Q: 6.q4

A: Detailed explanation:(a)Resolution of an ADC is the smallest change in voltage that can be detected;…

Q: Discuss the significance of analog-to-digital converters (ADCs) in microcontroller applications.…

A: The above question is based on the application of ADCs in microcontroller-based applications.

Q: A 12-bit counting converter with VFS = 5 V and fc = 1 MHz has an input voltage VX = 3.760 V. (a)…

A: (a) The expression for ADC output code is given by output code = input voltageoutput voltgae2n bits…

Q: C. Convert a 10.2 V using 4 bits Successive-Approximation Analog-to-Digital Converter and sketch the…

A: We need to convert a 10.2 V using 4-bits successive approximation Analog-Digital Converter and we…

Q: 1. Explain the difference between digital and analogue electronics devices, and then Explain the…

A: Digital devices:- In digital devices signals are discrete in time and values. Signals are…

Q: For the BJT circuit shown in Figure b, find the operation point of the transistor. (use B=100 for…

A: Solution: The modified circuit is,

Q: A 20-bit dual-ramp converter is to have an integration time T1 = 0.2 s. How rapidly must the unknown…

A: Given: T1= 0.2 s, n= 20, N= 0.1

Q: Q1: Assume a 12 bits ADC is used to convert analog signal with Vin = 2.6V and Vref = 4V, what is the…

A: Types of ADC Successive Approximation Flash ADC Dual Slope ADC Delta-sigma ADC.........ETC…

Q: A voltage regulator is rated at an output current of I, = 0 to 40 mA. Under no-load conditions, the…

Q: Q3: Using 4-bits successive approximation A/D converter, explain with sketching the required figures…

A: The ADC is an analog to digital convertor. The machines understand the digital binary bits in their…

Q: Temperature coefficient of resistance. 3. Simplify the Boolean function below and draw the…

Q: R V, (o1) = V m sin(œx) Since R = 10, L = 3 mH, Vs = 100sin(2n50t) and a = 120o in the following…

A: Considering the load current is constant. Evaluating the output voltage of the single phase…

Q: In following figure, Q1 and Q2 are identical and %3D operate in active mode. if Ic1 = 7.5 Ic2 then…

Q: An n-channel JFET has lpss = 20 mA and Vp=23 V. If the gate-source voltage is VGS= -1.5 V, find the…

A: Given: and , and ,we need to find:differentiate with respect to VGS to find small-signal…

Q: Q1: Determine all the output waveforms for the 74HC195 when its input signals are shown below CLK J…

A: Given data: Waveforms for Input signals to a 74HC195 IC are given, CLK, J, K', SH/LD', CLR', D0, D1,…

Q: QUESTIONS 1. There are two functions of a transistor, that are fundamental to the design of…

A: A transistor is a semiconductor device used to amplify or switch electronic signals and electrical…

Q: TRUE OR FALSE Increasing R2 increases the single-ended and double-ended differential mode gains of…

A: BJT is a current controlled Device in which base current control the mode of operation of BJT . Mode…

Concept explainers

Digital to Analog Converters

Digital to analog converters are commonly known as DAC, digital analog converter, D2A, or Digital-to-Analog converters. DACs are one of the important devices used in the electronics and electrical domain. DACs are the systems that convert a digital signal into an analog signal, whereas an analog to digital converter or ADC performs the opposite function. Digital signals are those signals that can represent the information or data as a set of discrete values. At a particular instant of time, a digital signal can only take a particular value of data. A digital signal is characterized by two unique values; zeros and ones, or true and false, represented by the Boolean domain. These are also known as binary signals or logic signals. Unlike digital signals, an analog signal is represented by continuous values, where at any time instant, the analog signal is represented by a real number.

Question

An 8-bit DAC has a reference voltage of 5V. What would be the voltage corresponding to a binary
word of 10010011?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which of the following can be used in amplifier circuits? а. Photodiodes b. Transistors C. Zener diodes d. Rectifiers
An RTD is to be used as a temperature sensor and has a resistance at 0°C of 198 ohms. It forms one arm of a wheatstone bridge being balanced at this temperature and each of the other arms also being 198 ohms. If the temperature coefficient of the RTD material is 0.0075/K, what will be the output voltage in millivolts from the bridge per degree change in temperature if the supply voltage is 11.01V? No label, no unit, number only. Differential amplifier ... Offset ουtput Power supply Compensation lines RTD Add your answer
Digital Electronics and Design Questiona) Write a 2:1 MUX module using Verilog-HDL.b) Use the module in (a) and write a Verilog-HDL code to implement a 4:1 MUX.
In the transfer characteristics shown below in Figure A, Vh is: [Approximate time to answer: 2 Minutes.] ID (mA)† Vth •VG$ (V) Figure A Minimum Drain Current Maximum Ig Minimum gate voltage Maximum Drain Voltage
given that V1 = 10 volt and V2 = 20 volt . what is value of output voltage. explain ...
A 5-bit flash converter has a reference voltage of 16 V. What is the digitized output of 10.12 V?
An 8-bit analog to digital converter has a reference voltage of 5 Volts. (i) Find the digital output if the input voltage is 4.175 Volts? (ii) What should be the required input to get an output of 11001100?
A platinum RTD PT100 measures 100 Q at 0 °C and 139.1 Q at 100 °C. Calculate temperature in °C if Temperature Coefficient of RTD PT100 is given as 0.0066 and resistance is 105.2(0). O 7.16 O 7.88 O 10.91 O 8.04
Q2: What are the types of base band digital moxdulation and explain one of its. nu tuchnioues used
a. A 220 ohms resistor is connected in series with the gate of an SCR using basic circuit in figure. The gate current required to fire the SCR is 10mA.What is the input voltage (Vin) is necessary to switch on the SCR?
21. Ipss = 20 mA and Vgs(off) = –-6 V for a particular JFET. %3D (a) What is Ip when Vcs = 0 V? (b) What is Ip when VGs = VGs(off? (c) If Vcs is increased from -4 V to –1 V, does I, increase or decrease?
Proj 2: Design MCU system to find distance of an object and print the distance on LCD, when the distance is less than 20 cm, a green led is turn on and when the distance become less than 12 cm, a red led should be turned on and when it is less than 10 cm, a warning sound generated from buzzer is turned on.