An 1500 kg automobile has springs with k = 1.4×104 N/m. One of the tires is not properly balanced; it has a little extra mass on one side compared to the other, causing the car to shake at certain speeds. Part A If the tire radius is 42 cm, at what speed will the wheel shake most? Express your answer using two significant figures.

An 1500 kg automobile has springs with k = 1.4×104 N/m. One of the tires is not properly balanced; it has a little extra mass on one side compared to the other, causing the car to shake at certain speeds. Part A If the tire radius is 42 cm, at what speed will the wheel shake most? Express your answer using two significant figures.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 54PQ

See similar textbooks

Similar questions

Determine the force-couple system at O which is equivalent to the two forces applied to the shaft AOB. Is R perpendicular to Mo? Assume F1 = 600 N, F2 = 610 N, a = 75 mm, b = 170 mm, 0 = 20°, and o = 54°. A a b. B F, Answer: R = (i i+ i j+ i k) N Mo = ( i i+ i j+ i k) N-m
Ⓒ Macmillan Learning A pipe system consists of three pipes with lengths L₁ = 1.80 m, L₂ = 0.600 m, and L3 = 2.50 m. A plumber pulls on the end of the pipe system, at the point P, with a force Fp = -24.0 Ni + 45.0 Nj + 35.0 NK. What is the torque 7 due to Fp about the origin? Enter your expression using ijk unit vector notation. 7 = Incorrect 4₁ P -43.2i +27j +87.5k N.m
A traffic light hangs from a pole as shown in the figure ( Figure 1). The uniform aluminum pole AB is 7.40 m long and has a mass of 11.0 kg. The mass of the traffic light is 23.0 kg. Determine the tension in the horizontal massless cable CD. Figure 3.80 m C 37° A T = 距 ΑΣΦ Submit Request Answer Part B ? N Determine the vertical component of the force exerted by the pivot A on the aluminum pole. ΜΕ ΑΣΦ 1 of 1 Fp,vertical = B Submit Request Answer 000 Part C ? N Determine the horizontal component of the force exerted by the pivot A on the aluminum pole. Fp,horizontal= ΜΕ ΑΣΦ ? N
The particle of mass m = 2.2 kg is attached to the light rigid rod of length L = 0.80 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity = ω = 3.9 rad/s. Determine the force T in the rod when θ = 33°. The force T is positive if in tension, negative if in compression. 1. Calculate the r- and θ-components of acceleration. 2. Determine the force T in the rod when θ = 33°
A uniform spool is suspended from a vertical wall by a string attached to the spool’s thin axle. The axle is horizontal, as shown below. The wall is smooth, so it exerts no frictional force on the spool. The tension in the string is 2.6 N. What is the weight of the spool? a 1.2 N b 1.0 N c 0.5 N d 2.4 N e 2.6 N
Part A Two metal disks, one with radius R1 = 2.40 cm and mass M = 0.900 kg and the other with radius R2 = 5.05 cm and mass M2 = 1.70 kg , are welded together and mounted on a frictionless axis through their common center. A light string is wrapped around the edge of the smaller disk and a 1.60 kg block is suspended from the free end of the string. What is the magnitude of the downward acceleration of the block after it is released? Take the free fall acceleration to be 9.80 m/s?. a = m/s? Submit Request Answer Part B Repeat the calculation of part (a), this time with the string wrapped around the edge of the larger disk. Take the free fall acceleration to be 9.80 m/s?. ? a = m/s² Submit Request Answer
A pendulum is made of a uniform solid sphere with mass M and radius R suspended from the end of a light rod. The distance from the pivot at the upper end of the rod to the center of the sphere is L. The pendulum's moment of inertia Ip for rotation about the pivot is usually approximated as ML?. Part A Use the parallel-axis theorem to show that if R is 5 % of L and the mass of the rod is ignored, Ip is only 0.1 % greater than ML². Essay answers are limited to about 500 words (3800 characters maximum, including spaces). 3800 Character(s) remaining Submit Request Answer Part B If the mass of the rod is 1 % of M and R is much less than L, what is the ratio of Irod for an axis at the pivot to ML2 ? Express your answer using two significant figures. P Pearson
A rotating door is made from four rectangular glass panes, as shown in the figure. The mass of each pane is 93.5 kg. A person pushes on the outer edge of one pane with a force of F = 88.2 N that is directed perpendicular to the pane. Determine the magnitude of the door's angular acceleration. Number i Units 1.2 m > 1.2 m
Open Response 1: This is a multi-part problem. Please answer all parts here. A bar (m = 1.5 kg, L = 1 m) is supported by a string that is 0.3 m from one end. Two masses, m1 and m2, hang from either end of the bar, as shown in the figure. The size of m1 is unknown and m2 = 0.75 kg. The system is in equilibrium. 1 2, a. How big is m1? b. What is the tension in the string?
A square metal plate 0.180 m on each side is pivoted about an axis through point o at its center and perpendicular to the plate (Figure 1). For related problemsolving tips and strategies, you may want to view a Video Tutor Solution of Applying a torque. Figure F2 0.180 m 0.180 m 45° F3 F1 1 of 1
A slender rod with length L has a mass per unit length that varies with distance from the left-hand end, where = 0, according to dm/dx = y, where y has units of kg/m². For related problemsolving tips and strategies, you may want to view a Video Tutor Solution of Uniform sphere with radius r, axis through center. Part A Calculate the total mass of the rod in terms of Y and L. Express your answer terms of the variables y and L. ΓΙΑΣ. 6 IXI ? X. 10m ⒸHAR M= Submit Previous Answers Request Answer * Incorrect; Try Again; 3 attempts remaining The correct answer does not depend on: ML. Part B Use I = fr² dm to calculate the moment of inertia of the rod for an axis at the left-hand end, perpendicular to the rod. Use the expression you derived in part A to express I in terms of M and L. Express your answer in terms of the variables M and L. ΠΙΑΣΦΗ I = Submit Request Answer Part C Repeat part B for an axis at the right-hand end of the rod. Express your answer in terms of the variables M and L.…
Part C In which case is less force required? case A O case B