PROBLEM 3An axial flow pump has the following data:Rotational speed750 rpmDischarge of water1.75m3/sHead7.5mHub to runner diameter ratio0:45Through flow velocity is 0.35 times the peripheral velocity.Find the diameter, andA. 7.11 mВ. 7.3 mC. 1.5 mD. 0.59 mminimum speed ratio.А. 1.7B. 0.83С. 3.0D. 4.01

diameter= 0.59m minimum speed ratio= 0.83

Answered: al flow pump

Engineering

Mechanical Engineering

al flow pump

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

02 h, are 12m. The pump efficiency is 79%, and the pump is driven by an electric motor. A pump moves water @10°C from a lake into a large, pressurized holding tank as shown. The flow rate, Q. is 375 L/min, and the piping system losses, 1) Sketch the setup (simple schematic is good), 2) label the z datum, and 3) identify and label the boundary conditions (P, V, and z) at 1 and 2 for use in a) the General Energy Equation (GEE). Provide values and units for the boundary conditions. Hint: For identifying good locations for boundary conditions, where are the velocities approximately zero? b) Calculate the head added to the fluid, h,, by the pump. Give your answer in units of m. Hint: Be careful with signs in manipulating the GEE. Show as many steps as you need to get your h, equation correct. Calculate the power added to the fluid by the pump in units of kW. () Determine the required electric motor size to drive the pump in units of HP. Prank = 200 kPa Holding Tank Air 6 m Pump Lake
PROBLEM 4 A centrifugal pump delivers 26 l/s against a total head of 16m at 1450 rpm. The impeller diameter is 0.5 m. A geometrically similar pump of 30 cm diameter is running at 2900 rpm. Assuming equal efficiencies between the two pumps. Calculate the head, and A. 11.52 m В. 12.03 m C. 40.7 m D. 6.09 m discharge required. A. 8.01/s B. 6.5 l/s C. 11.23 l/s D. 7.5 l/s
A centrifugal pump has a 41.5-in-diameter impeller. It is used to deliver water at about 12,000 gal/min. Its pump performance curve when spun at 710 RPM is shown in the figure below. If the impeller is trimmed to a new diameter of 39.5in, estimate the new head (in feet) and flow (in gal/min or GPM) if the speed is not changed. a. 11244 gpm, 283 ft b. 11422 gpm, 283 ft c. 11422 gpm, 238 ft
A two branch duct system of circular duct is shown below. The fittings have the following equivalent lengthof straight duct upstream to branch 4m elbow 2m. There is negligible pressure loss in the straight throughsection of the branch. The designer slects 3m/s as the air velocity in all branch sections.What diameter in ft should be selected in the 5 m branch section? A. 2.136 B. 0.340 C. 0.651 D. 1.050
Using affinity laws, develop a pump curve and BHP curve for a 1 ½" AB pump for a 6" impeller. Use a 1750 rpm curve as the "known" characteristics and develop a theoretical curve using affinity laws for 3500 rpm based upon flow rates 0, 20, 40, 60, 80 and 90 gpm at 1750 rpm. Plot the theoretical (affinity-based) and published flow vs. head and flow vs. horsepower curves for 3500 rpm.
Consider a family of turbines each having a flow coefficient phi = 0.4 blade aspect ratio H / b = 3 and Reynolds number Re = 10 ^ 5 Calculate and plot ne and ne versus degree of reaction for stage loading factors V of 1, 2 and 3 using Soderberg's correlation. For each loading factor find the degree of reactions which yield maximum nt and ns ,respectively
Calculate the brake horspower for the 38 inch dia. pump for capacity equal to 20000 gpm 710 min 25 400 NPSH 20 15 350 -41in dia 10 300 38-in dia 86% 250 -35-in dia 84% 1500 bhp 200 to 1250 bhp 150 100 28 12 10*** US galka peet minute Total head, f $09 NPSH, fA
PROBLEM 4 A centrifugal pump delivers 26 Vs against a total head of 16m at 1460 rpm. The impeller diameter is 0.5 m A geometrically similar pump of 30 cm diameters running at 2900 rom. Assuming equal efficiencies between the two pumps. Calculate the head, and A. 11.52 m B12.03 m C.40.7 m D. 6.09 m discharge required. A. 8.01/s 865/s c1 23 Vs D. 7.5 l/s
This course EHide block A centrifugal pump with the following impeller dimensions is used to pump water. The pump is running at 1000 rpm. The ideal head rise through the pump is 190 ft. b2 Poz 72 by The parameters of the impeller are as follows: r2= 9in, b2=3in, B2= 31° Take g= 9.81 m/s23 32.2 ft/s2 pw = 998 kg/m3 = 1.94 Slug/ft. Determine the theoretical flow rate in gpm Choose.. Determine the theoretical Power shaft in (hP) Choose...
Example (6-1): At the best efficiency point a centrifugal pump, with impeller diameter D=8 in, produces H= 21.9 ft at Q=300 gpm with N=1170 rpm. Compute the corresponding specific speed using a) U.S. customary units. B) SI units (rad/sec, m/sec, m'/sec").c) European units (rev/sec, m/sec, m/sec?). Develop conversion factors to relate the specific speeds.
Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m'/sec. 3. Specific speed.
A given centrifugal pump works at a flow coefficient Cf=0.65 The pump has a diameter of 3.0 cm and a the out surface 1.3 cm^2 and runs at rotation speed of 800 rpm What is the actual flow rate? give you answer in Liter/min Your Answer: Answer units