ArialCDE1Question 3Airplane of 150 tonnes reaches the speed of 900 km/h and altitude of 12.0 km. Its enginesproduce 100 MW of power.a) Convert all the above information into Sl units without prefixes (1 tonne = 1000 kg). Usescientific notation where appropriate.b) Calculate the kinetic energy the airplane acquires when it reaches the given speed.c) Calculate the potential energy of the airplane once it reaches the specified height.d) Given its speed and height, what is the total mechanical energy of the airplane?e) Given the power of its engines, calculate the time it would take to reach the stated speedand altitude. Express your answer in seconds.

Kinetic energy is generally the energy an engine has because of its motion. potential energy is…

Airplane of 150 tonnes reaches the speed of 900 km/h and altitude of 12.0 km. Its engines produce 100 MW of power. a) Convert all the above information into SI units without prefixes (1 tonne 1000 kg). Use scientific notation where appropriate. b) Calculate the kinetic energy the airplane acquires when it reaches the given speed.

Airplane of 150 tonnes reaches the speed of 900 km/h and altitude of 12.0 km. Its engines produce 100 MW of power. a) Convert all the above information into SI units without prefixes (1 tonne 1000 kg). Use scientific notation where appropriate. b) Calculate the kinetic energy the airplane acquires when it reaches the given speed.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 32P

See similar textbooks

Similar questions

An airplane has a mass of 48,000 kg, a wing area of 300 m2, a maximum lift coefficient of 3.2, and a cruising drag coefficient of 0.03 at an altitude of 12,000 m. Determine (a) the takeoff speed at sea level, assuming it is 20 percent over the stall speed, and (b) the thrust that the engines must deliver for a cruising speed of 900 km/h.
A jet is flying through air at a speed of 1250 km/h. Calculate Q5. Mach Number: the Mach number of the aircraft is the air temperature is -40°C. I
Fluid Mechanics Unit Conversions: a) The given gas conditions are p=35psi, T=100o Farenheit, and the gas constant for the gas being R=1716ft*lbf/(slug*oR), calculate the density of the gas using the density from the Ideal Gas Law, rho=p/RT, in the units lbm/ft3 b) The power, P, that a bicycle needs to ride at at velocity V against a drag force F is FV. If V=24mph and F=10lbf, compute the calories burned on a one hour bike ride.
Express each of the following in Sl units 1.) 50 IN-LB 2.) 500 KWH 3.) 20 IN/HR
A JET PLANE WHICH WEIGHT 29430 N AND HAS A WING AREA OF 20 M² FLIES AT A VELOCITY OF 250 KM/HR. WHEN THE ENGINE DELIVERS 7357.5 KW, 65% OF THE POWER IS USED TO OVERCOME THAT DRAG RESISTANCE OF THE WING. CALCULATE THE CO-EFFICIENT OF LIFT AND CO-EFFICIENT OF DRAG FOR THE WING. TAKE DENSITY OF AIR EQUAL TO 1.21 KG/M³.
Please solve the problem quickly including the free body diagram. I have 30mins
As most of you know, commercial transport planes cruise at an altitude of approximately 10,000 m. The power required to maintain level flight depends on air drag or resistance at that altitude, which may be estimated by the relationship 1 power = Pe C„AU³ air where pr is density of air at the given altitude, C, represents the drag coefficient of the plane, A is the planform area, and U represents the cruising speed of the plane. Assume that a plane is moving at constant speed and, C, remaining constant, determine the ratio of power that would be required when the plane is cruising at 8000 m and when the plane is cruising at 11,000 m.
UNIVERSITY OF ANBAR 01: Calculate the weight density, specific volume and specific gravity of a liquid having a volum of 6m and weight of 44kN.
The 1.9-Mg car increases its speed uniformly from rest to 17 m/s in 28 s up the inclined road. Part A Determine the maximum power that must be supplied by the engine, which operates with an efficiency of € = 0.8. (Figure 1) Express your answer with the appropriate units. Figure 10 ? ΜΑ Pmax = Value Units 1 of 1 Submit Request Answer Part B Also, find the average power supplied by the engine Express your answer with the appropriate units. HA ? Pavg= Value Units
Question 4 of 10 0/1 E View Policies Show Attempt History Current Attempt in Progress In a diesel engine the fuel is ignited when it is injected into hot compressed air, heated by the compression itself. In a typical high-speed diesel engine, the chamber in the cylinder has a diameter of 10.7 cm and a length of 13.4 cm. On compression, the length of the chamber is shortened by 12.7 cm (a “5-inch stroke"). The compression of the air changes its pressure from 1.00 to 39.5 atm. The temperature of the air before compression is 391 K. As a result of the compression, what will be the final air temperature (in Kand °C) just before the fuel injection? temperature = K = i °C eTextbook and Media Hint Assistance Used Determine the volume change as a way to get a handle on the new temperature. What equation relates pressure, temperature, and volume? The volume of the cylinder = z r² (height). Remember that the radius is half the diameter. Save for Later
A cylindrical tank with flat ends has diameter of two meters and is 5m long. It is mounted on a pedestal with axis parallel to the ground. It is filled to a depth of 1.5m. Find the volume of fuel in the tank in liters. A. 12650L B. 11470L C. 10640L D. 13420L
Gasoline at 20°C is pumped through a smooth 12-cm-diameter pipe 10 km long, at a flow rate of 75 m'/h (330 galpain). The inlet is fed by a pump at an absolute pressure of 24 atm. The exit is at standard atmospheric pressure and is 150 m higher. Estimate the frictional head loss h, and compare it to the velocity head of the flow V/(2g). (These numbers are quite realistic for liquid flow through long pipelines.)